Geophysics and the search of freshwater bodies: A review

Geophysics may assist scent dogs and divers in the search of water bodies for human and animal remains, contraband, weapons and explosives by surveying large areas rapidly and identifying targets or environmental hazards. The most commonly applied methods are described and evaluated for forensic searches. Seismic reflection or refraction and CHIRPS are useful for deep, open water bodies and identifying large targets, yet limited in streams and ponds. The use of ground penetrating radar (GPR) on water (WPR) is of limited use in deep waters (over 20 m) but is advantageous in the search for non-metallic targets in small ditches and ponds. Large metal or metal-bearing targets can be successfully imaged in deep waters by using towfish magnetometers: in shallow waters such a towfish cannot be used, so a non-metalliferous boat can carry a terrestrial magnetometer. Each device has its uses, depending on the target and location: unknown target make-up (e.g. a homicide victim with or without a metal object) may be best located using a range of methods (the multi-proxy approach), depending on water depth. Geophysics may not definitively find the target, but can provide areas for elimination and detailed search by dogs and divers, saving time and effort.     

Testing Application of Geographical Information Systems,Forensic Geomorphology and Electrical Resistivity Tomography to Investigate Clandestine Grave Sites in Colombia,South America

Colombian forensic investigators required assistance locating clandestine burials of missing persons related to human right atrocities from 14 years ago. Geoscientific search methods were trialled, including a predictive spatial statistical model, using various input and database information, to select the most likely grave locations in difficult mountainous terrain. Groundwork using forensic geomorphology, near-surface geophysics (ERT) and subsequent probing identified suspect burial positions. One site was in mountainous terrain and the other in former school grounds, both difficult to access and in poor weather conditions. In the mountainous area, a negative resistivity anomaly area was identified and intrusively investigated, found to be a buried rock. In school grounds, after MESP and intelligence were used to identify a burial site, surface depressions were identified, and ERT datasets collected over the highest priority depression; intrusive investigations discovered a hand-dug pit containing animal bones. This approach is suggested for Latin American searches.     

A GIS‐based Quantitative Approach for the Search of Clandestine Graves,Italy

Previous research on the RAG color‐coded prioritization systems for the discovery of clandestine graves has not considered all the factors influencing the burial site choice within a GIS project. The goal of this technical note was to discuss a GIS‐based quantitative approach for the search of clandestine graves. The method is based on cross‐referenced RAG maps with cumulative suitability factors to host a burial, leading to the editing of different search scenarios for ground searches showing high‐(Red), medium‐(Amber), and low‐(Green) priority areas. The application of this procedure allowed several outcomes to be determined: If the concealment occurs at night, then the “search scenario without the visibility” will be the most effective one; if the concealment occurs in daylight, then the “search scenario with the DSM‐based visibility” will be most appropriate; the different search scenarios may be cross‐referenced with offender's confessions and eyewitnesses’ testimonies to verify the veracity of their statements.     

Establishing forensic search methodologies and geophysical surveying for the detection of clandestine graves in coastal beach environments

A 2010 UK police search for a clandestine burial highlighted the need for more information and quantitative data to aid coastal beach searches. This study aimed to address this by establishing relevant forensic search methodologies to aid the search for clandestine coastal burial sites, using the North West English coastline as a search area. A set of parameters were established, including criteria such as tidal range, proximity to vehicular access points and distance from inhabited areas, which may inform forensic searches by prioritising likely locations of clandestine burials. Three prioritised coastal locations were subsequently identified: (1) coastal dunes at Formby, (2) coastal dunes and (3) beach foreshore at Southport, all sites part of the Liverpool City Region in the United Kingdom. At all locations, simulated clandestine graves were hand-dug by spades into which a naked adult-sized, metal-jointed fiberglass mannequin was buried at 0.5 m below ground level. Trial geophysical surveys were then undertaken with the aim of identifying the optimal geophysical instrumentation and technique to deploy in such environments. GPR data showed 450 MHz frequency antennae to be optimal, with significantly poor data obtained from the foreshore area due to saline seawater. Electrical resistivity and magnetic susceptibility surveys were successful in coastal environments in target detection (albeit not in non-vegetated sand dunes), with resistivity fixed-offset configurations deemed optimal. The latter survey successes may be due to the recent disturbed 'grave' rather than the target, which itself is of interest in terms of identifying the most recent clandestine burials.     

Soilwater Conductivity Analysis to Date and Locate Clandestine Graves of Homicide Victims

In homicide investigations, it is critically important that postmortem interval and postburial interval (PBI) of buried victims are determined accurately. However, clandestine graves can be difficult to locate; and the detection rates for a variety of search methods (ranging from simple ground probing through to remote imaging and near‐surface geophysics) can be very low. In this study, simulated graves of homicide victims were emplaced in three sites with contrasting soil types, bedrock, and depositional environments. The long‐term monthly in situ monitoring of grave soil water revealed rapid increases in conductivity up to 2 years after burial, with the longest study evidencing declining values to background levels after 4.25 years. Results were corrected for site temperatures and rainfall to produce generic models of fluid conductivity as a function of time. The research suggests soilwater conductivity can give reliable PBI estimates for clandestine burials and therefore be used as a grave detection method.     

Detecting buried metallic weapons in a controlled setting using a conductivity meter

Forensic personnel may face a daunting task when searching for buried weapons at crime scenes or potential disposal sites. In particular, it is common to search for a small firearm that was discarded or buried by a perpetrator. When performing forensic searches, it is recommended to first use non-invasive methods such as geophysical instruments to minimize damage to evidence and to the crime scene. Geophysical tools are used to pinpoint small areas of interest across a scene for invasive testing, rather than digging large areas throughout the site. Prior to this project, there was no published research that tested the utility of the conductivity meter to search for metallic weapons such as firearms and blunt and sharp edged weapons. A sample comprised of 32 metallic weapons including firearms, blunt and sharp edged weapons, and scrap metals was buried in a controlled setting to test the applicability of a conductivity meter for forensic searches. Weapons were tested at multiple depths and after data collection was performed for one depth, the weapons were reburied 5 cm deeper until they were no longer detected. Variables such as weapon size, burial depth, transect interval spacing (25 and 50 cm), and metallic composition were tested. All of the controlled variables influenced maximum depth of detection. For example, size was a factor as larger weapons were detected at deeper depths compared to smaller weapons. Metal composition affected maximum depth of detection as the conductivity meter detected items comprised of ferrous metals at deeper depths than non-ferrous metals. Searches for large buried items may incorporate a transect interval spacing of 50 cm but small weapons may be undetected between transects and therefore a transect interval spacing of 25 cm is recommended. Overall, the conductivity meter is a geophysical tool to consider when searching for larger-sized metallic weapons or to use in conjunction with an all-metal detector, particularly when searching for buried metallic evidence in obstructed areas.     

A clandestine burial in Costa Rica: prospection and excavation

Abstract:  This case report describes the search for a clandestine grave in Costa Rica for which the police sought the assistance of an archaeologist. An anonymous informant suggested that the victim had been kidnapped and murdered, placed in a shallow grave in the woods, then covered with lime and cement. A search of the area to detect conventional signs of burial (e.g., slumping, different plant growth) resulted in excavation of unrelated features of past disturbance. Different aspects of the grave including the deposition of cement powder over the body prevented its initial discovery. Improvisation of conventional archaeological excavation methods and use of police familiar with archaeological excavation resulted in the location of the grave and exhumation of the victim without loss of important contextual evidence that supported testimony on the cause of death. The taphonomic effects of high-lying ground water and lime in the tropical burial environment are briefly discussed. Recommendations such as the construction of a temporary sump to lower the ground water level in the grave during excavation are made to assist in similar investigations in the future.     

Suspect graveyard burial (South Armagh,N. Ireland): Combined search,forensic anthropology and radiocarbon dating

Geophysical investigation of a former convent graveyard for conversion to a community centre identified an unrecorded, unmarked burial below a later burial. Archaeological excavation confirmed the presence of skeletonized human remains, considered by police as a possible clandestine burial. Mortuary examination indicated the remains belonged to a mature adult female. To determine whether the deceased could be a recorded missing person, radiocarbon dating was undertaken on a femur and a rib bone. This is not always straightforward, and results showed two possible ages due to intercepts on either side of the nuclear weapons testing spike in atmospheric ¹⁴C; however, the later dated burial allowed us to constrain the date of a rib to CE 1959. This study demonstrates that dating a second tissue with a longer turnaround time, such as a femur, can help to constrain which side of the bomb spike is most probable. This paper documents in one work the search, scene and sample and then advances this to resolution by anthropological analysis and radiocarbon dating of human remains.     

Use of thermal drone in detection and assessment of larval mass temperature in decomposed rabbit carcasses

Manual ground searches and cadaver dogs are traditional methods for locating remains, but they can be time- and resource-intensive, resulting in the decomposition of bodies and delay in victim identification. Therefore, thermal imaging has been proposed as a potentially useful tool for detecting remains based on their temperature. This study investigated the potential of a novel search technique of thermal drones to detect surface remains through the detection of maggot mass temperatures. Two trials were carried out at Selangor, Malaysia, each utilizing 12 healthy male Oryctolagus cuniculus European white rabbits and DJI Matrice 300 RTK drone China, equipped with a thermal camera; Zenmuse H20T to record the thermal imaging footage of the carcasses at various heights (15, 30, 60–100 m) for 14 days for each trial. Our results demonstrated that the larval masses and corresponding heat emissions were at their largest during the active decay stage; therefore, all the carcasses were observable in thermal images on day 5 and remained until day 7. Statistical analyses showed that (1) no statistically significant differences in thermal images between clothed and unclothed subjects (p > 0.05); (2) 15 m above ground level was proven to be the optimal height, as it showed the greatest contrast between the carcass heat signature and the background (p < 0.005). Our data suggested the potential window of detection of thermal signatures was detectable up to 7 days post-deposition. This could be an important guideline for the search and recovery teams for operational implementation in this tropical region.     

The Search for “Fred”: An Unusual Vertical Burial Case,

Police witness intelligence stated a murdered adult male “Fred” had been vertically buried in wooded hilly terrain 30 years ago in the Midlands, U.K. Conventional search methods were unsuccessful; therefore, the police requested a geophysical investigation to be undertaken to determine whether “Fred” could be detected. A multiphased geophysical approach was conducted, using bulk ground conductivity and metal detectors, then follow‐up magnetics and ground penetrating radar (GPR) survey profiles on electromagnetic (EM) anomalous areas. A tight grid pattern was used to account for the reduced target size. Relatively high‐resolution EM and GPR techniques were determined optimal for this terrain and sandy soil. Geophysical anomalies were identified and the most promising intrusively investigated, and this was found to be a large boulder and tree roots. Study implications suggest careful multiphase geophysical surveys are best practice and give confidence in cold case searches. This study yielded a no‐body result, effectively saving police time and costs from further investigations.     

Geophysical Monitoring of Simulated Clandestine Graves Using Electrical and Ground‐Penetrating Radar Methods: 0–3 Years After Burial*,†

Abstract: This study provides forensic search teams with systematic geophysical monitoring data over simulated clandestine graves for comparison to active cases. Simulated “wrapped” and “naked” burials were created. Multigeophysical surveys were collected over a 3‐year monitoring period. Bulk ground resistivity, electrical resistivity imaging, multifrequency ground‐penetrating radar (GPR), and grave and background “soil‐water” conductivity data were collected. Resistivity surveys revealed the naked burial had consistently low‐resistivity anomalies, whereas the wrapped burial had small, varying high‐resistivity anomalies. GPR 110‐ to 900‐MHz frequency surveys showed the wrapped burial could be detected throughout, with the “naked” burial mostly resolved. Two hundred and twenty‐five megahertz frequency GPR data were optimal. “Soil‐water” analyses showed rapidly increasing (year 1), slowly increasing (year 2), and decreasing (year 3) conductivity values. Results suggest resistivity and GPR surveys should be collected if target “wrapping” is unknown, with winter to spring surveys optimal. Resistivity surveys should be collected in clay‐rich soils.     

Application of forward‐looking infrared (FLIR) imaging from an unmanned aerial platform in the search for decomposing remains

Traditional methods of cadaver detection in outdoor environments include manual ground search, cadaver dogs, and manned aerial reconnaissance during daylight. These methods have limitations; however, a potential low‐cost alternative may be to employ thermal imaging equipment mounted on an unmanned aerial vehicle (UAV) to detect heat emitted by insect and bacterial activity on the decomposing remains. No studies have addressed the influence of wrappings on detection of maggot mass thermal signatures nor assessed thermal detection of smaller body fragments. We addressed these knowledge gaps by utilizing a two‐phase experimental approach to explore thermal detection of carcasses using UAV‐mounted infrared imaging. In Phase 1, pig body fragments were deposited on the surface or shallow buried. In Phase 2, whole pig carcasses were deposited in four conditions: on the surface uncovered, wrapped in plastic or carpet, or buried. Our results demonstrated that observable heat emissions from remains corresponded to peak insect activity during active decay and could be readily detected in uncovered whole carcasses and fragments. Although plastic and carpet wrappings partly impeded detection of insect heat signatures, these materials were clearly detectable themselves because of their contrast to the background ground surface. Thermal signatures of buried partial remains and disturbed gravesoil were also observed; however, the buried whole carcass transitioned to adipocere prior to the decay stage and without any insect colonization or heat signature. These data can inform operational implementation of this technique to complement existing search strategies to offer a robust, low‐cost alternative for use where scene characteristics allow.     

The detection of clandestine graves in an arid environment using thermal imaging deployed from an unmanned aerial vehicle

The Middle East is one of the world regions that has frequently suffered from armed conflicts that resulted in mass burials. However, the detection of clandestine graves in such an arid environment by deploying remote sensing payload on unmanned aerial vehicles (UAVs) has received little attention. The present study used a UAV equipped with a thermal sensor aimed at narrowing down the search area of possible gravesites in the arid climate of Kuwait. The enclosed research area, which includes both control and experimental mass graves, was imaged for 18 months. The variation in topsoil temperature and soil moisture between the graves and their surroundings was evaluated. The results of the analysis demonstrated the effectiveness of thermal imaging techniques in detecting heat produced from buried sheep carcasses and detecting the change in grave soil moisture for our research environment for 7 and 10 months, respectively. The buried animals significantly influenced the topsoil temperature (p = 0.044), while the height from which the images were captured had an insignificant effect on the measured temperature within the range tested (p = 0.985). Furthermore, there was a negative correlation (−0.359) between grave temperature and the calculated soil moisture. The results from these cost- and time-effective search methods presented in this study confirm their potential for the detection of burial sites in an arid environment.     

Search and Seizure, Racial Profiling, and Traffic Stops: A Disparate Impact Framework

In response to nationwide attention to the issue of racial profiling, numerous law enforcement agencies have reexamined their policies and collected data on the racial demographics of motorists stopped and searched by police. This article advocates a "disparate impact" framework for understanding the relationship between race and searches and seizures. Using data on the Washington State Patrol, analysis indicates that disparities in the proportions of racial minorities searched by the Patrol are likely not the result of intentional or purposeful discrimination. Additionally, factors such as age, sex, time of day, and the number of violations that motivated the stop affect the likelihood of a search.     

Long‐term Geophysical Monitoring of Simulated Clandestine Graves using Electrical and Ground Penetrating Radar Methods: 4–6 Years After Burial

This ongoing monitoring study provides forensic search teams with systematic geophysical data over simulated clandestine graves for comparison to active cases. Simulated “wrapped,” “naked,” and “control” burials were created. Multiple geophysical surveys were collected over 6 years, here showing data from 4 to 6 years after burial. Electrical resistivity (twin electrode and ERI), multifrequency GPR, grave and background soil water were collected. Resistivity surveys revealed that the naked burial had low‐resistivity anomalies up to year four but then difficult to image, whereas the wrapped burial had consistent large high‐resistivity anomalies. GPR 110‐ to 900‐MHz frequency surveys showed that the wrapped burial could be detected throughout, but the naked burial was either not detectable or poorly resolved. 225‐MHz frequency GPR data were optimal. Soil water analyses showed decreasing (years 4 to 5) to background (year 6) conductivity values. Results suggest both resistivity and GPR surveying if burial style unknown, with winter to spring surveys optimal and increasingly important as time increases.     

The application of dual energy X-ray soil screening in forensic archaeology

The need to forensically search soil for small artefacts at a burial site or traces of evidence in a deposition site is a common task shared by investigators and forensic archaeologists. In forensic casework, the importance of finding small pieces of evidence, such as personal effects or ballistic fragments, cannot be overstated as it can assist in the positive identification of the deceased, give an insight into the manner and cause of death, and identify any perpetrators. The soil search methods known as wet and dry sieving, are cumbersome, time-consuming and have limited success for some soil types. This often leads to the decision not to search, resulting in missed opportunities to identify potential evidence.The primary aim of this study was to investigate if a dual energy X-ray baggage scanner could be used to search for items of potential forensic interest in soil. A trial was conducted using a Smiths Detection ScanTrailer 100100 V-2is mobile X-ray inspection system to establish if it could be used to detect organic, inorganic, and metallic items located within soil. The soil type and natural variables such as water and organic content were adjusted to simulate different environments. The baggage scanner was found to provide a quick and easy way to detect items contained within various soil types, particularly in a sand rich matrix. It is estimated that using this method to search 1 m³ of soil, when broken down into samples that are < 13 cm in depth, would take around one hour to complete, compared with 100 to 150 person-hours by manual sieving. This is believed to be the first use of dual energy X-ray technology for this purpose and shows the potential for further research and use of this method in forensic archaeology.     

The effect of the burial environment on adipocere formation

Adipocere is a decomposition product comprising predominantly of saturated fatty acids which results from the hydrolysis and hydrogenation of neutral fats in the body. Adipocere formation may occur in various decomposition environments but is chiefly dependent on the surrounding conditions. In a soil burial environment these conditions may include such factors as soil pH, temperature, moisture and the oxygen content within the grave site. This study was conducted to investigate the effect of these particular burial factors on the rate and extent of adipocere formation. Controlled laboratory experiments were conducted in an attempt to form adipocere from pig adipose tissue in model burial environments. Infrared spectroscopy, inductively coupled plasma-mass spectrometry, and gas chromatography-mass spectrometry were employed to determine the lipid profile and fatty acid composition of the adipocere product which formed in the burial environments. The results suggest that adipocere can form under a variety of burial conditions. Several burial factors were identified as enhancing adipocere formation whilst others clearly inhibited its formation. This study acts as a preliminary investigation into the effect of the burial environment on the resultant preservation of decomposing tissue via adipocere formation.     

Biomedical waste disposal--Nuclear Regulatory Commission. Final rule

The NRC is amending its regulations to permit licensees greater leeway in disposing of liquid scintillation media and animal carcasses containing tracer levels of hydrogen-3 (tritium) or carbon-14. These rule changes will primarily affect NRC licensed hospitals and medical research institutions. Most licensees presently dispose of these items by sending them to a radioactive waste burial ground or by obtaining special authorization from NRC for incineration or onsite burial. Under the new regulations, the licensee may dispose of specified concentrations of these materials without regard to their radioactivity. The NRC is also amending its regulations to raise the annual limits for disposal of hydrogen-3 and carbon-14 by release to the sanitary sewerage systems. The rule changes will conserve waste burial capacity that is already in short supply.     

Extended reality (XR) virtual practical and educational eGaming to provide effective immersive environments for learning and teaching in forensic science

Online virtual learning resources have been available for learning and teaching in forensic science for some years now, but the recent global COVID-19 related periods of irregular lockdown have necessitated the rapid development of these for teaching, learning and CPD activities. However, these resources do need to be carefully constructed and grounded in pedagogic theory to be effective. This article details eXtended Reality (XR) learning and teaching environments to facilitate effective online teaching and learning for forensic geoscientists. The first two case studies discussed in this article make use of Thinglink software to produce virtual learning and teaching XR resources through an internet system, which was delivered to undergraduate students in 2021. Case one details a range of XR virtual laboratory-based equipment resources, providing a consistent, reliable and asynchronous learning and teaching experience, whilst the second case study presents an XR virtual learning applied geophysics resource developed for a 12-week CPD training programme. This programme involves recorded equipment video resources, accompanying datasets and worksheets for users to work through. Both case studies were positively received by learners, but there were issues encountered by learners with poor internet connections or computer skills, or who do not engage well with online learning. A third case study showcases an XR educational forensic geoscience eGame that was developed to take the user through a cold case search investigation, from desktop study through to field reconnaissance and multi-staged site investigations. Pedagogic research was undertaken with user questionnaires and interviews, providing evidence that the eGame was an effective learning and teaching tool. eGame users highly rated the eGame and reported that they raised awareness and understanding of the use of geophysics equipment and best practice of forensic geoscience search phased investigations. These types of XR virtual learning digital resources, whilst costly to produce in terms of development time and staff resource, provide a complementary virtual learning experience to in-situ practical sessions, and allow learners to asynchronously familiarise themselves with equipment, environments and techniques resulting in more efficient use of in situ time. The XR resources also allow learners to reinforce learning post in-situ sessions. Finally, XR resources can provide a more inclusive and authentic experience for learners who cannot attend or complete work synchronously.     

Eristalinus arvorum (Fabricius, 1787) (Diptera: Syrphidae) in Human Skull: A New Fly Species of Forensic Importance

A body of an unknown adult female was found within a shallow burial ground in Malaysia whereas the skull was exposed and visible on the ground. During autopsy examination, nine insect larvae were recovered from the interior of the human skull and subsequently preserved in 70% ethanol. The larvae were greyish in appearance, each with a posterior elongated breathing tube. A week after the autopsy, more larvae were collected at the burial site, and some of them were reared into adults. Adult specimens and larvae from the skull and from the burial site were sequenced to obtain DNA barcodes. Results showed all adult flies reared from the burial site, as well as the larvae collected from the skull were identified as Eristalinus arvorum (Fabricius, 1787) (Diptera: Syrphidae). Here, we report the colonization of E. arvorum larvae on a human corpse for the first time.