Internal Validation of Human Mitochondrial DNA Quantification Using Real‐Time PCR

The quantity of mitochondrial DNA (mtDNA) template added for amplification and subsequent dye terminator reactions is critical for obtaining quality sequence data. Validation of a human mtDNA real‐time quantitative PCR (qPCR) assay demonstrated its high degree of reproducibility and precision as well as an extremely sensitive threshold of detection (0.0001 pg/μL or approximately six human mtDNA copies/μL). A study of 35 nonprobative bone and teeth evidence samples revealed that 20 pg of mtDNA template is recommended for successful HV1 and HV2 sequence analysis; however, as little as 0.013 pg can generate a full mtDNA profile when using enhanced amplification reactions. The assay can also detect PCR inhibition and is useful for identifying samples that may benefit from re‐purification. Overall, the assay is an excellent method to quantify mtDNA and is useful for determining the best analytical approach for successful sequencing.     

Characterizing the Performance of Pipe Bombs

Pipe bombs of steel or PVC fragment in reproducible patterns when similarly configured. The power of the explosion correlates with number, mass, and size of the fragments recovered, where a large number of small, low‐mass fragments indicate a high‐power event and vice versa. In discussing performance, describing pipe fragmentation pattern by fragment weight distribution mapping (FWDM) or fragment surface area distribution mapping (FSADM) was useful. When fillers detonated, detonation velocities of ~4.4 mm/μs were measured. In such cases, side walls of the pipe were thrown first; the average fragment velocity was ~1000 km/s. In deflagrations, the end cap was first thrown; fragment velocities were only ~240 km/s. Blast overpressures varied; at 10 feet, 2 × 12 inch steel pipes containing ~550 g of detonable mixture produced overpressures of 5–6 psi; similar nondetonating pipes produced less than 2 psi. Maximum fragment throw distances were 250–300 m, with an average of ~100 m.     

Voltammetric determination of cocaine in confiscated samples using a cobalt hexacyanoferrate film-modified electrode

In this work, a fast, non destructive voltammetric method for cocaine detection in acetonitrile medium using a platinum disk electrode chemically modified with cobalt-hexacyanoferrate (CoHCFe) film is described. The deposition of CoHCFe film at platinum disk (working electrode) was carried out in aqueous solution containing NaClO₄ at 0.1 mol L⁻¹ as supporting electrolite. Stability studies of the film and subsequent voltammetric analysis of cocaine were made in acetonitrile medium with NaClO₄ at 0.1 mol L⁻¹ as supporting electrolite. A reversible interaction between cocaine and CoHCFe at the film produces a proportional decrease of original peak current, due to the formation of a complex between cocaine and cobalt íons, with subsequent partial passivation of the film surface, being the intensity of current decrease used as analytical signal for cocaine. A linear dependence of cocaine detection was carried out in the range from 2.4 × 10⁻⁴ to 1.5 × 10⁻³ mol L⁻¹, with a linear correlation coefficient of 0.994 and a detection limit of 1.4 × 10⁻⁴ mol L⁻¹. The analysis of confiscated samples by the proposed method indicated cocaine levels from 37% to 95% (m/m) and these results were validated by comparison to HPLC technique, being obtained good correlation between both methods.     

Surface Curvature of Pelvic Joints from Three Laser Scanners: Separating Anatomy from Measurement Error

Recent studies have reported that quantifying symphyseal and auricular surface curvature changes on 3D models acquired by laser scanners has a potential for age estimation. However, no tests have been carried out to evaluate the repeatability of the results between different laser scanners. 3D models of the two pelvic joints were generated using three laser scanners (Custom, Faro, and Minolta). The surface curvature, the surface area, and the distance between co‐registered meshes were investigated. Close results were found for surface areas (differences between 0.3% and 2.4%) and for distance deviations (average <20 μm, SD <200 μm). The curvature values were found to be systematically biased between different laser scanners, but still showing similar trends with increasing phases/scores. Applying a smoothing factor to the 3D models, it was possible to separate anatomy from the measurement error of each instrument, so that similar curvature values could be obtained (p < 0.05) independent of the specific laser scanner.     

The indirect transfer of glass fragments to a jacket and their subsequent persistence

Experiments were conducted to investigate a scenario sometimes encountered in casework, where a police officer has attended a scene and shortly afterwards arrested a suspect. The experiments involve the transfer of glass fragments from a surface scattered with broken glass to a hand, and then from the hand to the sleeve of a poorly retaining jacket. The persistence of the transferred fragments was studied by collecting the glass fragments as they fell off the jacket, whilst the wearer was walking on the spot. The recovery regime allowed the number and proportion of fragments picked up and transferred to the jacket from the hand to be determined, and the rate at which they were lost from the jacket to be monitored. The results show that large numbers of glass fragments can be picked up on a hand from a suitable surface. A subsequent firm grip to a poorly retaining jacket was found to transfer a significant proportion of the glass fragments from the hand to the jacket. In seven of nine tests performed, ten or more glass fragments were recovered from the jacket 60 minutes after the original contact between the hand and the broken glass. More than twenty fragments were recovered in three of these tests. Consequently, where possible and appropriate, the full circumstances of a case should be considered carefully before indirect transfer is ruled out as a possible explanation for recovered “matching” glass. This is the case even for poorly retaining clothing.     

Detection of Pb,Ba, and Sb in Cadaveric Maggots and Pupae by ICP-MS*

The concentrations of lead (Pb), barium (Ba), and antimony (Sb), characteristic of GSR, were determined in soil sediments and immature (larvae) of cadaveric flies of the family Calliphoridae, by inductively coupled plasma mass spectrometry (ICP-MS). This research refers to a case study from two real crime scenes in which the corpses were in an advanced state of decomposition. In case 1, the victim had holes similar to gunshot wounds, and in case 2, there was no evidence of perforations in the corpse. Soil sediment collection was performed at three different points of the terrain, at a minimum distance of 10 m from the corpse, for cases 1 and 2. In relation to the collection of immatures, larvae were collected in regions of the mouth, nose, and orifices similar to the entry of firearms projectile into the body, for case 1, and collection of larvae and pupae, located on the body and underneath it, for case 2. It was possible to detect and quantify the three elements of interest (Pb, Ba, and Sb) by ICP-MS in both sediment and cadaveric larvae. Concentrations of 4.44, 8.74, and 0.08 μg/g were obtained for Pb, Ba, and Sb, respectively, in the soil for case 1. For the case 2, the concentrations in Pb, Ba, and Sb were from 16.34 to 26.02 μg/g; from 32.64 to 57.97 μg/g and from 0.042 to 0.30 μg/g, respectively. In the larvae, Pb, Ba, and Sb were quantified in cases 1 and 2 with a concentration of 6.28 and 1.78 μg/g for Pb, 1.49 and 2.94 μg/g for Ba, 0.50 μg/g and <LD for Sb, respectively. These new results present the detection of characteristic elements of GSR in cadaveric larvae in humans in a real crime scene, besides highlighting the importance of the study of immature flies, using the ICP-MS technique in forensic analysis.     

Chemical Imaging of Human Fingermark by X-ray Photoelectron Spectroscopy (XPS)

X-ray photoelectron spectroscopy (XPS) is a widely used technique to characterize the surface chemistry of materials. It plays a crucial role in accessing qualitative and quantitative information and in detecting the presence of chemical functional groups on the surface of any material. The forensic methods available to detect and identify elements and organic/inorganic compounds are often destructive, so evidence cannot be re-analyzed. However, XPS allows rapid analysis of samples without damaging them. Recently, an increasing number of forensic researchers have begun to study certain chemical information on fingermarks. In this study, the authors aimed to present the applicability and power of XPS imaging in fingermark analysis which can also provide specific information about the fingermark chemical composition. Herein, monochromated X-ray (Al Kα) spot size was fixed at 50 μm. XPS mapping resulted in the acquisition of spectra at each pixel, in an array of 41 × 30 pixels with a step size of 50 μm. Then, a simple discussion has been made about how the scanned surface spectrum and basic snapshot spectra are used to identify different components at a fingertip of a scanned surface area (~3 mm²). Hence, a fingermark pattern contaminated with caffeine, TiO₂, and Pb/PbO deposited on the silicon wafer can be chemically mapped and visualized by XPS using principal component analysis (PCA). Thus, the present study showed the possible applicability of XPS for the identification of illicit drugs of abuse, gunshot residue, and skin care products on latent fingermark by mimicking a crime scene evidence.     

Systematical method for polyacrylamide and residual acrylamide detection in cosmetic surgery products and example application

IntroductionIn this paper, the authors presented a case of acrylamide poisoning in a middle-aged woman who had underwent unsuccessful cosmetic surgery six years earlier. The victim was told that the product that had been injected into her face was Restylane®, which mainly contained sodium hyaluronate and was the first and only Food and Drug Administration (FDA)-approved dermal filler for lip enhancement in the USA for more than 20 years. Widespread facial infections occurred several years post-injection; finally, the victim had to undergo removal surgery. Acrylamide poisoning was strongly suspected based on the victim's clinical manifestation. The product that had been injected into the victim's face was probably polyacrylamide hydrogel-based product, which had been prohibited by the State Food and Drug Administration (SFDA) in China in 2006. To confirm this suspicion, a systematical method was established to differentiate varieties of cosmetic surgery products and identify residential acrylamide.MethodsThe removed objects, original products and a certified reference sample of Restylane® were collected for examination. A direct microscopic examination was applied as a rapid screening method. Fourier transform infrared (FTIR) microspectroscopy analysis was subsequently performed to distinguish the main components from each sample. Automated solid phase extraction, ultra high performance liquid chromatography (SPE UHPLC) analysis was ultimately utilised and optimised to detect the residual acrylamide. Chromatographic separation was achieved on an ACQUITY UHPLC HSS T3 column. The mobile phase consisted of 0.01% aqueous formic acid solution and acetonitrile. The tunable UV (TUV) detection wavelength was at 202 nm.ResultsThe microscopic examination indicated that different samples had different morphological characteristics, depending on their main components. The FTIR spectrum showed that different polymers could be distinguished according to the CO stretching vibration (1655 cm^? 1), NH bending vibration (1540 cm^? 1) and CO stretching vibration (1078 and 1045 cm^? 1). The UHPLC results demonstrated that the calibration curve was linear in the range of 0.5–20.0 μg/mL, with a correlation coefficient of 0.999. The average recoveries of the method were 99–107% with an RSD of 1.6–6.3%. The detection limit was 0.1 μg/mL (S/N = 3). The analytical time was 6 min per sample. Acrylamide was detected in the allegedly Restylane® injection.ConclusionsThis systematical method provides a rapid, accurate and sensitive determination of polyacrylamide and residual acrylamide. The microscopic and FTIR spectroscopic examinations help to verify the existence of polyacrylamide quickly and easily. The optimised SPE UHPLC-TUV method offers a simpler and more sensitive approach to confirm the amount of acrylamide, comparing to the methods in the literature.     

Nondestructive Differentiation of Polyester Single White Fibers Using Synchrotron Radiation Microbeam X-ray Fluorescence Spectrometry with Vertical Focusing

In this study, the nondestructive differentiation of individual white polyester clothing fibers was accomplished via synchrotron radiation microbeam X-ray fluorescence (SR-μ-XRF) analysis. SR-μ-XRF with vertical focusing is a useful nondestructive method for the analysis of a single polyester clothing fiber. Kirkpatrick–Baez (KB) mirror was used to vertically focus 20 keV X-rays for the analysis of 22 individual white polyester fibers taken from clothing commonly sold in Japan. SR-μ-XRF with a vertical focused 2 μm (V) × 300 μm (H) beam was approximately 12.8 times more sensitive than SR-XRF with an unfocused 300 μm (V) × 300 μm (H) beam for the detection of elements in single fibers. The minimum detection limits (MDLs) of the SR-μ-XRF method were 8.15 ppm for Cl and 0.06 ppm for Br. In addition to Ti in TiO₂ delustering agents, Zr and Nb impurities in the delustering agents were detected in individual fibers. Sb from a polymerization catalyst and Co from a transesterification catalyst were also detected in individual fibers. Comparing the Ti K_β/Sb L_α,β and Zr K_α/Nb K_α X-ray intensity ratios was a useful way to distinguish individual clothing fibers, and 98% of the fibers were differentiated when additional trace elements were used as discrimination indicators.     

Multidrug poisoning involving nicotine and tramadol

A fatal case of multidrug poisoning by tramadol and nicotine is reported. Tramadol is a centrally acting analgesic used in the treatment of moderate to severe acute or chronic pain. Nicotine, a lipid-soluble alkaloid, is one of the most readily available drugs in modern society. A 46-year-old man was found dead in his bed, and a suicide note was discovered near the body. He had 25 transdermal nicotine patches attached to his thorax and abdomen. Two half emptied bottles were found on the bedside table; the toxicological examination revealed that they contained tobacco and nicotine as well as other drugs such as diphenhydramine. At autopsy, areas of fresh and old myocardial infarction as well as diffuse pulmonary congestion and edema were present. The tramadol concentration was 6.6 μg/mL in femoral venous blood, while levels of nicotine and its primary metabolite cotinine were determined to be 0.6 and 2.0 μg/mL in femoral venous blood. Based on these results, we determined the cause of death to be cardiorespiratory failure induced by the additive effects of tramadol and nicotine shortly after consumption.     

Effects of Cyanoacrylate Fuming,Time After Recovery,and Location of Biological Material on the Recovery and Analysis of DNA from Post‐Blast Pipe Bomb Fragments*

Abstract: This study investigated the effects of time, cyanoacrylate fuming, and location of the biological material on DNA analysis of post‐blast pipe bomb fragments. Multiple aliquots of a cell suspension (prepared by soaking buccal swabs in water) were deposited on components of the devices prior to assembly. The pipe bombs were then deflagrated and the fragments recovered. Fragments from half of the devices were cyanoacrylate fumed. The cell spots on the fragments were swabbed and polymerase chain reaction/short tandem repeat analysis was performed 1 week and 3 months after deflagration. A significant decrease in the amount of DNA recovered was observed between samples collected and analyzed within 1 week compared with the samples collected and analyzed 3 months after deflagration. Cyanoacrylate fuming did not have a measurable effect on the success of the DNA analysis at either time point. Greater quantities of DNA were recovered from the pipe nipples than the end caps. Undeflagrated controls showed that the majority (>95%) of the DNA deposited on the devices was not recovered at a week or 3 months.     

A Comparison of Fingerprint Sweat Corrosion of Different Alloys of Brass

Fingerprint sweat from 40 donors was deposited onto samples of five α and α + β phase brasses, comprising five alloys with different copper and zinc concentrations, two of which also had the addition of small concentrations of lead. Visual grading of the visibility of the corrosion revealed that brasses with the least amount of zinc produced the most visible and fully formed fingerprints from the most donors. Consideration of previously reported mechanisms for the corrosion of brass suggests red copper (I) oxide as a likely corrosion product for low zinc brasses, and a consideration of the color, composition, and solubility of fingerprint sweat corrosion products suggests that copper (I) oxide produces good contrast and visibility with the brass substrate. Scanning electron microscope images of the corrosion of all five alloys confirmed the enhanced contrast between corroded and uncorroded areas for low zinc alloys.     

Analysis of hair after contamination with blood containing cocaine and blood containing benzoylecgonine

In post-mortem work, blood is a potential source of external contamination of hair. The present study was carried out to investigate the amount of drug absorbed into hair which has been contaminated with blood containing either cocaine or BE. Solutions were prepared containing 0.05, 0.1, 0.2, 0.5 and 3.0 μg/mL of either cocaine or BE in human blood. Samples of approximately 3.2 g of drug-free hair were contaminated by soaking in the blood solutions for 5 min. They were then removed and left at room temperature. Approximately 0.5 g of hair was collected from each of the blood soaked hair samples at 6 h, 1, 2, 4 and 7 days after contamination. As each hair sample was collected it was shampoo-washed to prevent further drug absorption. Hair samples were analysed in triplicate using a fully validated method described previously. EME and cocaethylene were also measured in order to find out if cocaine or BE was breaking down to these compounds. Both cocaine and BE were absorbed into hair in significant concentrations when the concentration in the blood was 0.5 μg/mL or greater; cocaine was more readily absorbed than BE. Cocaine broke down to EME (<LOQ) at 0.5 μg/mL and to EME (>LOQ) and BE (<LOQ) at 3.0 μg/mL. When the blood concentration of cocaine was 0.5 μg/mL or less, there was no evidence of it breaking down to form BE. From the samples soaked in blood containing BE, there was no evidence of the BE breaking down. The absorption of drug into hair did not increase as the contamination period increased from 6 h to 7 days.     

Optimization of Headspace Solid‐Phase Microextraction Technique for Extraction of Volatile Smokeless Powder Compounds in Forensic Applications

Smokeless powders are low explosives and are potentially found in cases involving firearms and improvised explosive devices. Apart from inorganic compound analysis, forensic determination of organic components of these materials appears as a promising alternative, especially the chromatographic techniques. This work describes the optimization of a solid‐phase microextraction technique using an 85 μm polyacrylate fiber followed by gas chromatography‐flame ionization detection for smokeless powder. A multivariate experimental design was performed to optimize extraction‐influencing parameters. A 2⁴ factorial first‐order design revealed that sample temperature and extraction time were the major influencing parameters. Doehlert matrix design has subsequently selected 66°C and 21 min as the compromised conditions for the two predetermined parameters. This extraction technique has successfully detected the headspace compounds of smokeless powders from different ammunition types and allowed for their differentiation. The novel technique allows more rapid sample preparation for chromatographic detection of smokeless powders.     

Cannabinoids determination in oral fluid by SPME–GC/MS and UHPLC–MS/MS and its application on suspected drivers

The confirmation of Δ9-tetrahydrocannabinol (THC) in oral fluid (OF) is an important issue for assessing Driving Under the Influence of Drugs (DUID). The aim of this research was to develop a highly sensitive method with minimal sample pre-treatment suitable for the analysis of small OF volumes (100 μL) for the confirmation of cannabinoids in DUID cases. Two methods were compared for the confirmation of THC in residual OF samples, obtained from a preliminary on-site screening with commercial devices. An ultra high performance LC–MS (UHPLC–MS/MS) method and an SPME–GC/MS method were hence developed. 100 μL of the residual mixture OF/preservative buffer or neat OF was simply added to 10 μL of THC-D3 (1 μg/mL) and submitted to the two different analyses: A — direct injection of 10 μL in UHPLC–MS/MS in positive electrospray ionisation (ESI) mode and B — sampling for 30 min with SPME (100 μm polydimethylsiloxane or PDMS fibre) and direct injection by desorption of the fibre in the GC injection port.The lowest limit of detection (LLOD) of THC was 2 ng/mL in UHPLC–MS/MS and 0.5 ng/mL in SPME–GC/MS. In addition, cannabidiol (CBD) and cannabinol (CBN) could be detected in GC/MS equipment at 2 ng/mL, whilst in UHPLC–MS/MS the LLOD was 20 ng/mL.Both methods were applied to 70 samples coming from roadside tests. By SPME–GC/MS analysis, THC was confirmed in 42 samples, whilst CBD was detected in 21 of them, along with CBN in 14 samples. THC concentrations ranged from traces below the lowest limit of quantification or LLOQ (2 ng/mL) up to 690 ng/mL.     

Determination of Acetamiprid and IM‐1‐2 in PostMortem Human Blood,Liver, Stomach Contents by HPLC‐DAD

An HPLC‐DAD method was developed to detect and quantify a neonicotinoid insecticide acetamiprid (ATP) and its metabolite IM‐1‐2 in autopsy samples of a fatal intoxication case. The postmortem blood and tissue distribution of ATP and IM‐1‐2 was determined for the first time. The method showed acceptable precisions and recoveries with relative standard deviations of <10% for ATP level and 1.38 % for IM‐1‐2. The detection and quantification limits for ATP were 0.015 μg/mL and 0.030 μg/mL for blood and were 0.035 μg/g and 0.050 μg/g for liver samples, respectively. The mean contents of ATP were 0.79 μg/g in the liver, 47.35 μg/g in the stomach contents and 2.7 μg/mL in the blood. IM‐1‐2 content was 17.0 μg/g in the stomach contents. ATP and IM‐1‐2 were not detected in the urine. The presence of ATP and IM‐1‐2 in the samples was confirmed by GC‐MS. The method can be exploited in future forensic casework.     

Passport examination by a confocal-type laser profile microscope

The author proposes a nondestructive and highly precise method of measuring the thickness of a film pasted on a passport using a confocal-type laser profile microscope. The effectiveness of this method in passport examination is demonstrated. A confocal-type laser profile microscope is used to create profiles of the film surface and film–paper interface; these profiles are used to calculate the film thickness by employing an algorithm developed by the author. The film thicknesses of the passport samples—35 genuine and 80 counterfeit Japanese passports—are measured nondestructively. The intra-sample standard deviation of the film thicknesses of the genuine and counterfeit Japanese passports was of the order of 1 μm The intersample standard deviations of the film thicknesses of passports forged using the same tools and techniques are expected to be of the order of 1 μm. The thickness values of the films on the machine-readable genuine passports ranged between 31.95 μm and 36.95 μm. The likelihood ratio of this method in the authentication of machine-readable Japanese genuine passports is 11.7. Therefore, this method is effective for the authentification of genuine passports. Since the distribution of the film thickness of all forged passports was considerably larger than the accuracy of this method, this method is considered effective also for revealing the relation among the forged passports and acquiring proof of the crime.     

Towards molecular autopsies: Development of a FFPE tissue DNA extraction workflow

Sudden unexpected death (SUD) is a devastating event and forms a substantial proportion of the cases investigated at forensic mortuaries each year. Despite post-mortem investigations, the cause of death may remain undetermined. There is potential for these unresolved cases to benefit from retrospective molecular autopsies for investigation into genetic mutations which may have contributed towards death. Often, formalin fixed paraffin embedded tissues (FFPET) are the only archival sources of DNA available for retrospective analyses. However, extracting usable DNA from FFPET is challenging as current methods yield poor quality and quantity DNA. Thus, this study aimed to optimise DNA recovery from FFPET by investigating several variables within the DNA extraction workflow, including the selection of tissue type, number and thickness of tissue sections, deparaffinisation method, and DNA extraction kit. The quantity and quality of DNA recovered were assessed using spectrophotometry, real time PCR, digital capillary electrophoresis and DNA profiling. This study was the first to implement a nuclei quantification using microscopy to guide the selection of the best tissue type to use for DNA analysis. The use of a greater number of thinner tissue sections (100 sections, each 1 μm) significantly improved DNA concentration, purity and fragment length. Additionally, the combination of Deparaffinization Solution with the QIAamp® DNA FFPE Tissue Kit proved most favourable with a median DNA yield of 320 ng and 55% of DNA fragments greater than 400 bp. Isolated DNA was of single source, indicating no contamination in the workflow, and FFPET blocks that were stored for up to 3.5 years did not significantly affect DNA degradation (p = 0.1764). These results are especially informative for designing library preparation and sequencing workflows for determining cause of death in unresolved SUD cases.