The influence of polymer type, print donor and age on the quality of fingerprints developed on plastic substrates using vacuum metal deposition.

This study investigated fingerprint development on five different polymer substrates using vacuum metal deposition (VMD). The conditions required for optimum development are shown to depend on a number of factors. No one set of conditions will result in good development in all situations. Polymer type has been confirmed as a major factor in determining the types of development that will occur and the optimum VMD conditions required. For more consistently successful VMD development, polymer type should be determined before selecting conditions. While polymer type is a key factor in determining optimum development conditions, there may be variation of the optimum conditions within a polymer type, most likely due to the presence of additives in the plastic. The heaviness of a latent print, i.e. amount of residue that constitutes the print, also affects the VMD conditions required. The donor, manner of deposition, and age of a print affect the heaviness of the deposit. The heavier the print, the higher the gold count necessary for successful VMD development. The occurrence of 'empty prints' (i.e. zinc deposition on the general background but not on or between the print ridges) was found to be related to polymer type and print heaviness. Heavy prints on PVC and PET are the most likely to be 'empty' after VMD treatment. The development of empty prints may be due to the diffusion of print residue into the print valleys. Pre-treatment with cyanoacrylate fuming was also found to affect VMD development. In particular, it was shown that cyanoacrylate pre-treatment was beneficial for print development on PET and PVC. The results of this study were used to formulate guidelines for use as an aid by laboratories using VMD in casework.     

Vacuum metal deposition: developing latent fingerprints on polyethylene substrates after the deposition of excess gold.

A previously identified difficulty with the development of latent fingerprints on low-density polyethylene (LDPE) by vacuum metal deposition (VMD) is that excess gold deposition prevents effective zinc deposition and so inhibits latent print development [1]. The investigation of a means to correct for excess gold deposition was the basis for this study. Exposure to zinc and the readmission of air into the vacuum chamber followed by VMD development results in the deactivation of the initial gold clusters due to the formation of zinc oxide and the adsorption of air and water molecules. As a result, the majority of the gold deposited during the second treatment creates new gold clusters rather than adding to the gold clusters previously formed. After excess gold deposition on LDPE, the deposition of 1.5 times the optimum gold amount will result in good-quality normal development. The results also indicate that, on all surfaces, at least twice the initial gold count should be used for re-treatment when further development is required after air has been readmitted to the chamber.     

Vacuum metal deposition: visualisation of gold agglomerates using TEM imaging

Vacuum metal deposition (VMD) is a well-established technique that can be used for the development of latent fingermarks on a range of polymer surfaces, including polyethylene (PE) bags exposed to harsh environmental conditions. The technique has also proved to be effective on difficult semi-porous surfaces such as the polymer banknotes in circulation in Australia and in an increasing number of other countries. VMD is a two-stage technique. In the first stage, a small amount of gold is deposited under high vacuum onto the exhibit. This is then followed by the deposition, onto the gold layer, of a much thicker layer of zinc. Normal VMD development is characterised by zinc depositing all over the surface except on the fingermark ridges themselves. A phenomenon of reverse development (zinc on the ridges but not on the surface) has been reported by many authors. Recent studies indicated that this phenomenon might occur on low-density polyethylene (LDPE) when the amount of deposited gold is above an optimum quantity. The results suggested that the size of the gold agglomerates formed on the surface of the polymer plays a critical role. This preliminary study was aimed at visualising, by transmission electron microscopy (TEM), the formation of gold agglomerates on polymer surfaces to gain an appreciation of how the density and size of these agglomerates changes with an increasing amount of evaporated gold.     

Nanoscale analysis of the interaction between cyanoacrylate and vacuum metal deposition in the development of latent fingermarks on low-density polyethylene

Vacuum metal deposition (VMD) has been previously demonstrated as an effective development technique for latent fingermarks and in some cases has been shown to enhance prints developed with cyanoacrylate (CA) (superglue) fuming. This work utilizes scanning electron microscopy (SEM) to investigate the interactions of the two development techniques when applied to latent fingermarks on low-density polyethylene. CA is shown to act principally on the eccrine deposits around sweat pores, where polymerization results in long polymer fibrils a few 100 nm in width. Subsequent VMD processing results in additional areas of development, for example, between pores. However, the primary mode of deposition of zinc is by interaction with the polymerized CA, the fibrils of which become decorated with zinc nanoparticles. Areas with limited CA deposition and no significant polymerization are also enhanced with the VMD process, resulting in increased print development.     

Visualisation of fingermarks and grab impressions on fabrics. Part 1: gold/zinc vacuum metal deposition

Vacuum metal deposition (VMD) is a highly sensitive technique originally introduced for detecting latent fingermarks on smooth non-porous surfaces such as carrier bags, plastics and glass. The current study explores whether VMD can be used in the examination of clothing from physical and sexual assault cases in order to visualise identifiable fingermark ridge detail and/or palmar flexion crease detail, thus allowing potential areas to be indicated for DNA swabbing and/or to determine the sequence of events. Four different fabrics were utilised during this study - nylon, polyester, polycotton and cotton, along with 15 donors who ranged in their age and propensity to leave fingermarks, from good to medium to poor as determined by results obtained from test runs using paper and plastic carrier bags processed with VMD. Once samples were collected they were kept for a determined time (1, 2, 3, 4, 5, 6, 7, 14, 21 or 28 days) and then treated using the gold/zinc metal VMD process. From the results, it appears that greater ridge detail is visible on the smoother non-porous fabrics, such as nylon whereas on rougher porous fabrics, such as cotton, only empty prints and impressions, rather than any ridge details, were visible. All fabrics did however allow the development of touch marks that could be targeted for DNA taping thus potentially leading to a DNA profile and possible identification of a suspect.     

A comparison of the use of vacuum metal deposition versus cyanoacrylate fuming for visualisation of fingermarks and grab impressions on fabrics

Both vacuum metal deposition (VMD) and cyanoacrylate fuming (CAF) are techniques used to visualise latent fingermarks on smooth non-porous surfaces such as plastic and glass. VMD was initially investigated in the 1970s as to its effectiveness for visualising prints on fabrics, but was abandoned when radioactive sulphur dioxide was found to be more effective. However, interest in VMD was resurrected in the 1990s when CAF was also used routinely. We now report on studies to determine whether VMD or CAF is the more effective technique for the detection of marks on fabrics. Four different fabrics, nylon, polyester, polycotton and cotton, were utilised during this study, along with 15 donors who ranged in their age and ability to leave fingermarks, from good to medium to poor, thus reflecting the general population. Once samples were collected they were kept for a determined time (1, 2, 3, 4, 5, 6, 7, 14, 21 or 28 days) and then treated using either the gold and zinc metal VMD process or standard cyanoacrylate fuming.The smoother fabrics, such as nylon, consistently produced greater ridge detail whereas duller fabrics, like cotton tended only to show empty prints and impressions of where the fabric had been touched, rather than any ridge details. The majority of fabrics did however allow the development of touch marks that could be targeted for DNA taping which potentially could lead to a DNA profile. Of the two techniques VMD was around 5 times more effective than CAF, producing a greater amount of ridge detail, palmar flexion creases and target areas on more samples and fabrics.     

Ridge Width Correlations between Inked Prints and Powdered Latent Fingerprints

A methodology to estimate the time of latent fingerprint deposition would be of great value to law enforcement and courts. It has been observed that ridge topography changes as latent prints age, including the widths of ridges that could be measured as a function of time. Crime suspects are commonly identified using fingerprint databases that contain reference inked tenprints (flat and rolled impressions). These can be of interest in aging studies as they provide baseline information relating to the original (nonaged) ridges’ widths. In practice, the age of latent fingerprints could be estimated following a comparison process between the evidentiary aged print and the corresponding reference inked print. The present article explores possible correlations between inked and fresh latent fingerprints deposited on different substrates and visualized with TiO₂. The results indicate that the ridge width of flat inked prints is most similar to fresh latent fingerprints_, and these should be used as the comparison standard for future aging studies.     

影响真空镀膜显现手印效果的因素分析

目的考查真空镀膜技术在手印显现方面的应用。方法从影响真空镀膜法显现手印的因素展开,重点分析了喷镀距离、金的用量、客体悬挂角度、锌的蒸发电流和时间等对手印显现的影响。结果条件优化后可以增强手印纹线的立体感,改善金膜、锌膜在手印纹线和客体背景的分布情况,使显出的手印纹线反差明显。结论确定真空镀膜显现常见非渗透性客体上汗潜手印的最佳操作条件。     

Comparison of the Columnar‐Thin‐Film and Vacuum‐Metal‐Deposition Techniques to Develop Sebaceous Fingermarks on Nonporous Substrates,

Both the columnar‐thin‐film (CTF) and the vacuum‐metal‐deposition (VMD) techniques for visualizing sebaceous fingermarks require the deposition of a material thereon in a vacuum chamber. Despite that similarity, there are many differences between the two techniques. The film deposited with the CTF technique has a columnar morphology, but the film deposited with the VMD technique comprises discrete islands. A split‐print methodology on a variety of fingermarked substrates was used to determine that the CTF technique is superior for developing fingermarks on clear sandwich bags and partial bloody fingermarks on stainless steel. Both techniques are similar in their ability to develop fingermarks on glass but the CTF technique yields higher contrast. The VMD technique is superior for developing fingermarks on white grocery bags and the smooth side of Gloss Finish Scotch Multitask^? tape. Neither technique worked well for fingermarks on black garbage bags.     

A Preliminary Study on Vacuum Metal Deposition as a Standalone Method for Enhancement of Fingermarks on Ballistic Brass Materials

In order to assess the efficacy of vacuum metal deposition (VMD) as a technique to develop fingermarks on ballistic metallic surfaces, a preliminary study using six donors (three male & three female) was conducted. Using a sequential metal deposition process, two metal combinations were studied—gold/zinc and silver/zinc. Results indicate the potential of this technique, by developing identifiable fingermarks on brass metal disks aged from a few days up to more than a month old. As the development of fingermarks on fired (brass) cartridge cases is an area of interest, a further study was conducted where a total of 20 fingermarks were deposited on cases. After firing, second level fingermark characteristics were successfully observed on cartridge cases highlighting its potential as a fingermark enhancement method for ballistic brass materials. Further work is required to fully evaluate the VMD process and its reliability as a fingermark enhancing method on ballistic surfaces.     

Enhancement of Aged and Denatured Fingerprints Using the Cyanoacrylate Fuming Technique Following Dusting with Amino Acid‐Containing Powders

We have carried out experiments to investigate the aging of latent fingerprints deposited on black PVC over a period of 4–15 weeks. A thumbprint was used in each case and before deposition of the print the donor rubbed their thumb around their nose to add sebaceous deposits. We have studied the effect of heat, light, and moisture and we find that moisture is the most significant factor in the degradation of the latent print. We have attempted to enhance these latent prints by dusting with valine powder or powders composed of valine mixed with gold or red fluorescent commercial fingerprint powders. To make a direct comparison between “treated” and “untreated” prints, the prints were cut in half with one‐half being “treated” and one‐half not. Our studies show the best results being obtained when powders of valine and red fluorescent powders are applied prior to cyanoacrylate fuming.     

An efficient strategy to detect latent fingermarks on metallic surfaces

The aim of this work is to use metal sputtering for the development of latent fingermarks on metallic surfaces by taking advantage of the prints' topography. In order to promote the preferential deposition onto fingerprints' ridges the deposition parameters should be optimized. After a previous selection, copper and gold thin films were deposited by magnetron sputtering onto stainless steel substrates where fingermarks were intentionally placed. After optimizing the deposition parameters, the influence of the fingermarks' age was studied. The quality of the developed fingermarks was evaluated visually and through optical and scanning electron microscopy. The morphology of the copper and gold thin films was examined by high resolution scanning electron microscopy. The preferential magnetron sputtering deposition of copper and gold thin films, 20-30 nm thick, allows latent fingermarks to be successfully developed. The gold films are more promising, especially for detecting non-fresh fingermarks and for conserving the developed marks. It was possible to detect the contours of the ridges and localize minutiae features in a one-month aged impression developed by gold deposition. These films present discontinuous surface and columnar cross-sections, while copper thin films have a featureless morphology.     

Morphometry of latent palmprints as a function of time

In many crimes, the elapsed time between production and collecting fingermark traces is crucial. and a method able to detect the aging of latent prints would represent an improvement in forensic procedures. Considering that as the latent print gets older, substantial changes in the relative proportion of individual components secreted by skin glands could affect the morphology of ridges, morphometry could be a potential tool to assess the aging of latent fingermarks. Then, considering the very limited research in the field, the present work aims to evaluate the morphometry of latent palmprint ridges, as a function of time, in order to identify an aging pattern. The latent marks were deposited by 20 donors on glass microscope slides considering pressure and contact angle, and then were maintained under controlled environmental conditions. The morphometric study was conducted on marks developed with magnetic powder in 7 different time intervals after deposition (0, 5, 10, 15, 20, 25 or 30 days); 60 ridges were evaluated for each developed mark. The results showed that: 1) the method for the replacement and mixing of skin secretions on the palm was appropriate to ensure reproducibility of latent prints, and 2) considering the studied group, there was a time-dependent reduction in the width of ridges and on the percentage of visible ridges over 30 days. Results suggest the possibility of using the morphometric method to determine an aging profile of latent palmprints on glass surface, aiming for forensic purposes.     

Visualisation of fingermarks and grab impressions on dark fabrics using silver vacuum metal deposition

Vacuum metal deposition (VMD) involves the thermal evaporation of metal (silver) in a vacuum, resulting in a uniform layer being deposited on the specimen being treated. This paper examines the use of silver on dark fabrics, thus offering a simpler operation and more obvious colouration to that of the traditional use of gold and zinc metals which must be evaporated separately. The aim of this study was to investigate the effect of fabric type, donor, mark age and method of fingermark deposition on the quality of marks visualised using silver VMD. This was achieved by collecting fingermark deposits from fifteen donors, of both sexes and various ages, by a grab or a press method. Four different fabrics: satin, polyester, polycotton and cotton were studied over a 10 day timeline of 1, 2, 3, 4, 5, 6, 7, 14, 21 and 28 + days. It was found that satin and polyester gave the most positive results, with polyester often producing excellent ridge detail. Cotton and polycotton were less successful with no ridge detail being observed. The donors also had an observable effect on the results obtained probably due to variations in secretions produced or pressures applied during specimen collection. The age of the mark or the method of mark deposition had little influence on the results obtained. Silver VMD is a viable process for visualising marks on certain dark fabrics and has the advantage over gold/zinc VMD in that the marks visualised are light in colour which contrasts well against the dark background.     

Enhanced Visualization of Latent Fingermarks on Rough Aluminum Surfaces Using Sequential Au and Zn/ZnS/ZnO Depositions

Detection and visualization of fingermarks on rough and diffuse surfaces is a relatively challenging task. We succeeded in developing latent fingermarks on scratched and rough aluminum surfaces by sequential deposition of a thin layer of gold followed by one of zinc or zinc‐based compounds on the fingermarks. The best image enhancement was achieved with sequential Au and ZnS depositions. Using this combination, we could enhance the visualization of latent fingermarks aged over 65 days in normal conditions. The optical reflectance from the fingermarks with the deposited layers of metal/dielectric is analyzed as a stratified medium. Significant contrast in the reflectance from the regions of the ridges and the valleys of the fingermark would enhance the visualization. Our results show that the Au and ZnS bi‐layer combination can have a large reflection contrast and improved fingermark visualization at wavelengths corresponding to the green light for specific thickness of ZnS.     

Degradation of polymer banknotes through handling,and effect on fingermark visualisation

The surface structure of mint (as-issued) and handled polymer five pounds sterling banknotes was studied by atomic force microscopy and laser scanning confocal microscopy. A total of 1856 fingermarks on mint and handled banknotes from four different issuing banks (Bank of England, Bank of Scotland, Royal Bank of Scotland and Clydesdale Bank) were visualised with Vacuum Metal Deposition (VMD), Cyanoacrylate Fuming (CAF) and, on Clydesdale Bank notes, magnetic fluorescent powder. VMD was significantly more effective in developing fingermarks on handled banknotes, across all the banks studied, although effectiveness varied with issuing bank. For example, on handled Bank of England notes 45% of marks showed ridge detail with VMD development and 28% with CAF; for Bank of Scotland handled notes success rates were 17% with VMD and 1% with CAF. Microscopy of degraded banknotes showed the loss of intaglio printing and the formation of a cracked surface structure in the handled notes. These features can lead to the trapping of powder, or contaminants, increasing quantity of development agent in fingermark background between the ridges, decreasing contrast and decreasing performance of powder-based fingermark development techniques. These same features can restrict the migration of components of the fingermark, preventing fingermarks degrading through spread of material and thus reducing potential formation of empty prints, so that VMD development is not adversely affected.     

Distortion in Fingerprints: A Statistical Investigation using Shape Measurement Tools

Friction ridge impression appearance can be affected due to the type of surface touched and pressure exerted during deposition. Understanding the magnitude of alterations, regions affected, and systematic/detectable changes occurring would provide useful information. Geometric morphometric techniques were used to statistically characterize these changes. One hundred and fourteen prints were obtained from a single volunteer and impressed with heavy, normal, and light pressure on computer paper, soft gloss paper, 10‐print card stock, and retabs. Six hundred prints from 10 volunteers were rolled with heavy, normal, and light pressure on soft gloss paper and 10‐print card stock. Results indicate that while different substrates/pressure levels produced small systematic changes in fingerprints, the changes were small in magnitude: roughly the width of one ridge. There were no detectable changes in the degree of random variability of prints associated with either pressure or substrate. In conclusion, the prints transferred reliably regardless of pressure or substrate     

The optimisation of fingermark enhancement by VMD and Lumicyano™ on thermal paper

The enhancement of fingermarks on thermal paper can be challenging due to background staining caused by polar solvents used in fingermark enhancement techniques such as ninhydrin. This study explored a commercial one-step superglue fuming process, Lumicyano™, and Vacuum Metal Deposition (VMD) to develop fingermarks on this substrate and overcome this issue. Different sequential treatments involving Lumicyano™ and a combination of VMD methods were investigated with varying degrees of success with some sequences being highly sensitive. The VMD processes, however, were observed to generally be more effective at enhancing marks, whereas Lumicyano™ provided little or no benefit on this paper type. The results indicate that Lumicyano™ is only beneficial as a pre-treatment when the entire sequence of gold/zinc and silver/zinc is taken to completion. The gold/zinc and silver/zinc VMD processes were optimised on five different thermal papers, and the optimised techniques were then directly compared to determine which was more successful on each thermal paper type as a single treatment.     

溴甲酚绿与溴甲酚蓝显现液显现潜血印痕的比较

目的 探索一种犯罪现场上潜血印痕新型显现技术；方法 利用溴甲酚绿、溴甲酚蓝、四丁基碘化铵与酒精溶液作为新型潜血印痕显现液,研究该技术显现潜血印痕的效果,并与国内外最常用的四甲基联苯胺显现技术进行交叉比较；结果 新型溴甲酚绿和溴甲酚蓝酒精显现液对稀释浓度到为1/1000的潜血印痕的极其敏感,显现出的手印纹线清晰连贯、反差明显,无颜色背景,且能够有效增强四甲基联苯胺处理后潜血印痕；结论 新型潜血印痕显现技术反应灵敏、反差明显,能作为四甲基联苯胺的后处理试剂,若得到推广应用,将能够有效提高犯罪现场上潜血印痕的发现率、提取率和利用率.     

A Small Population Study on Friction Skin Ridges: Differences in Ridge Widths Between Latent and Inked Fingerprints

Morphological changes in the width of latent fingermark ridges occur naturally over time. This could be used to examine the aging process of latents and eventually estimate time of deposition. In a crime context, it is common practice to compare a questioned (aged) fingermark with a database of known (inked) prints. Therefore, in the absence of fresh fingermarks for aging purposes, it is of interest to reveal correlations between these two categories of fingerprints with regard to the widths of their ridges. The present study explores correlations of ridge widths between flat and rolled inked prints with latent fingermarks visualized with carbon black (CB) and titanium dioxide (TiO₂)-based powders among a small population of ten donors. Results revealed consistent differences between the ridge widths of latent and inked prints as well as flat and rolled impressions. Latent fingermarks visualized with CB and TiO₂ powders showed ridges with comparable widths.