Fluorescence spectra and images of latent fingerprints excited with a tunable laser in the ultraviolet region

Fluorescence spectra of sebum-rich latent fingerprints were studied with a tunable laser for non-destructive fingerprint detection without chemical treatment. The tunable laser consists of a nanosecond pulsed Nd-YAG laser and an optical parametric oscillator (OPO) crystal. The fluorescence spectra and images were measured at various excitation wavelengths in the ultraviolet region by the time-resolved fluorescence method. We have previously reported that a typical fluorescence spectrum of fingerprints consists of two peaks located at c. 330 and 440 nm. In order to determine the wavelength of optimal excitation, excitation spectra were measured at wavelengths ranging from 220 to 310 nm. The fluorescence intensity of the 330 nm peak became maximal with excitation at 280 nm. The images of latent fingerprints on white papers were also measured and the clearest image was obtained with excitation at 280 nm. The influence of continuous irradiation on the fluorescence of fingerprints was measured at the optimal excitation wavelengths. The 330 nm peak was strong at first and decreased with continuous irradiation, whereas the 440 nm peak, which was weak at first, increased gradually.     

Preliminary Study on Determining the Sequence of Intersecting Lines by Fluorescence Technique

The determination of the sequence of intersecting lines is an important part of questioned document examinations. A fluorescence technique was used to determine the sequence of heterogeneous intersecting lines produced using inkpad ink, stamp‐pad ink, ballpoint pens, gel pens, fountain pens, colorants of carbon paper, photocopiers, laser printers, and inkjet printers. A SteREO Discovery.V20 equipped with the ZEN Blue Lite software was chosen to perform the tests.As the results obtained from the study were positive under most conditions, the fluorescence technique was found to be very successful in determining the sequence of intersecting lines from ballpoint pen, gel pen, fountain pen, photocopier, laser and inkjet printers, and inkpad inks. The method was also successful in determining the sequence of intersecting lines from ballpoint pen, photocopier, laser printer, and stamp‐pad inks under most conditions. The technique was not successful in determining the order of crossing lines blending together.     

Visualization of latent fingerprints using fluorescence lifetime imaging on paper emitting strong fluorescence

Latent fingerprints were successfully visualized using fluorescence lifetime imaging (FLIM) on paper which emits strong fluorescence with a lifetime close to that of fingerprints and thus from which it is difficult for time-resolved spectroscopy to visualize fingerprints. Latent fingerprint samples on paper were excited using a 450 nm or 532 nm nanosecond pulsed-laser, and time-resolved fluorescence images were obtained at a delay time of 6–16 ns in intervals of 1 ns, to the excitation pulse. The excitation beam was expanded using a lens, and the fluorescence from the fingerprints was captured using an intensified CCD camera. Because of the large fluorescence intensity of the background paper of approximately two to four orders of magnitude larger than that of the fingerprint, the fingerprint was not visualized on each fluorescence image by time-resolved spectroscopy. However, the fingerprint was visualized in a FLIM image constructed using a series of the fluorescence images for the case with the fluorescence intensity of the background paper being four orders of magnitude larger than that of the fingerprint. The difference in fluorescence lifetime in the FLIM image of the visualized fingerprint and background paper was in the order of 0.1 ns, which was an order of magnitude smaller than the inherent fluorescence lifetime of a few nanoseconds for the fingerprints and paper. It was demonstrated that, at a background fluorescence intensity with a certain order of magnitude larger than that of fingerprints, FLIM has the potential to visualize latent fingerprints which cannot be visualized by time-resolved spectroscopy.     

An Examination of the Sequence of Intersecting Seal and Laser Printing Toner Line

Examining the sequence of intersecting seal and laser printing line is a significant method of determining the authenticity and validity of documents. In this study, five brands of stamp pad inks, three types of inkpads and seven kinds of laser printers were used to make heterogeneous line intersections. Observation method of physical characteristics, scraping technique and fluorescence method was used to determine the sequence of intersecting lines. Distinguishing features were noted between the materials produced in both sequences. As the results obtained from the study were positive, these features might provide a scientific basis for accurately determining the sequence between laser printing line and inkpad (stamp pad ink) seal.     

线聚焦显微激光拉曼光谱技术区分激光打印墨粉

目的利用Renishaw InVia激光显微拉曼光谱仪对打印墨粉进行区分。方法用785nm激发波长,采取线聚焦模式,50倍物镜条件下,测定了惠普等8个品牌25种硒鼓型号的30份激光打印机打印墨迹样品的拉曼光谱。结果 30种样品墨迹的谱图进行了分析,根据拉曼的异同,可将30种样品分为5大类。结论线聚焦显微激光拉曼光谱可用于区分不同种类激光打印墨粉。     

利用彩色文件上的图文特征鉴别喷墨打印机品牌

目的通过彩色文件上的图文特征鉴别喷墨打印机的品牌。方法在体视显微镜下观察采用不同喷墨机理的惠普、佳能和爱普生三大品牌喷墨打印机打印的彩色图文。结果通过对彩色图文上六种墨迹形态特征的比较,发现三大品牌喷墨打印机打印的彩色图文存在明显差异。结论依据这六种特征对三大品牌的喷墨打印机进行鉴别。     

Determining Line-Crossing Sequences Between Laser Printing and Writing Pen Using Coaxial Light

Determining the application sequence of hand-written pen ink and printer toner lines has attracted significant interest in questioned document examination. This study uses coaxial light to determine line-crossing sequences, with intersections observed under a VSC600 forensic document workstation and a Leica M205A Stereo-microscope. Results show that reflected light at intersections and color contrast between intersections and nonintersections was observed when a hand-written ink line passes over a toner line, while a toner line passing over a written line appeared dull, with no color contrast. The procedure was tested under a range of conditions, such as types of writing pens and laser printers, the writer, and writing pressure, with the latter playing an important role in the evaluation. To validate the results, a 90% detection rate and 98% accuracy rate were achieved from 50 samples of blind testing, which is more effective than optical microscopy.     

高仿真制模伪造指印的识别研究

目的 探究高仿真制模伪造指印的识别方法.方法 选取多个印泥指印作为母版,分别采用曝光法制作指模,将母版指印与对应的伪造指印进行整体比较及显微比较.结果 伪造指印较母版指印尺寸存在差异、纹线略变粗、纹线间隔略变小、细节特征易黏连、细小痕迹及细微特征不反映或反映不全、单根纹线的墨迹分布平实且缺少细微漏白等.结论 识别伪造指...     

显微共焦拉曼光谱技术区分喷墨打印机打印的彩色图文墨迹

目的建立显微共焦拉曼光谱法区分喷墨打印机打印的彩色图文墨迹的方法。方法利用显微共焦拉曼光谱技术所具有微量、微区、原位分析及非破坏性等特点,对24种常见彩色墨水墨迹分别进行检验。结果品红色墨点墨迹成分归类区分效果最好,其次是黄色墨点,最后是蓝色墨点。结论采用显微共焦拉曼光谱技术对彩色打印墨迹进行不同颜色单点分析可大大提高喷墨打印机厂家型号的识别率,是一种有效的检测手段。     

Determination of the Sequence of Intersecting Lines Between Toners and Seals by Laser Fluorescence Microscope

Fluorescence microscope is considered to be one of the most effective ways to examine the sequence of intersecting seal and toner lines of questioned documents. In reality, however, the toner (mainly divided into compact and noncompact toners) and seal of a questioned document have such a complex morphology and sequence of crossing lines that current methods cannot meet the requirement of practical document identification. In view of the challenges of document examination, a laser fluorescence microscope and method are developed in this study. The developed microscope provides additional functionality to traditional fluorescence microscopes of transmitted light modality, laser excitation, selectable excitation wavelength, and selectable fluorescence filters. The results obtained from the method of comparisons between transmitted light and fluorescence modalities were positive under most conditions, particularly for noncompact toner examination for which a 100% accuracy rate and 90% detection rate were achieved in blind testing.     

常用彩色激光打印机打印文件暗记特征的初步研究

目的收集当前我国常用不同品牌和型号的彩色激光打印机打印样本,研究打印文件上暗记特征的提取分析及其变化规律,探讨彩色激光打印文件暗记特征在鉴定实践中的应用及其在打印文件防伪措施中的价值。方法使用显微镜、文检仪及有关图像处理技术分别检验了彩色激光打印机的打印文件样本。结果彩色激光打印机打印文件上会出现暗记特征,且不同品牌的暗记特征出现规律、形态特征和点阵特征不同。结论暗记特征可作为初步鉴别彩色激光打印机品牌型号及打印时间的依据,具有防伪价值,但其在鉴定实践中还存在一定的局限性,有待进一步研究。     

Examination of heterogeneous crossing sequences between toner and rollerball pen strokes by digital microscopy and 3-D laser profilometry

The determination of line crossing sequences between rollerball pens and laser printers presents difficulties that may not be overcome using traditional techniques. This research aimed to study the potential of digital microscopy and 3-D laser profilometry to determine line crossing sequences between a toner and an aqueous ink line. Different paper types, rollerball pens, and writing pressure were tested. Correct opinions of the sequence were given for all case scenarios, using both techniques. When the toner was printed before the ink, a light reflection was observed in all crossing specimens, while this was never observed in the other sequence types. The 3-D laser profilometry, more time-consuming, presented the main advantage of providing quantitative results. The findings confirm the potential of the 3-D laser profilometry and demonstrate the efficiency of digital microscopy as a new technique for determining the sequence of line crossings involving rollerball pen ink and toner.     

Application of mist to fingermark detection: Misting with high-boiling-point liquid containing p-dimethylaminocinnamaldehyde and cyanoacrylate

In order to detect latent fingerprints that could be damaged by liquid or powder reagents, non-destructive processes such as gaseous reagents have been developed. In this report, we propose the use of fine mist generated when hot vapor of high-boiling-point liquids is rapidly cooled by surrounding air for fingermark detection. Octyl acetate (OA), 2-phenoxyethanol (2PE), and methyl decanoate (MD) were found to efficiently produce mist when heated to 230°C. By combining these liquids with p-dimethylaminocinnamaldehyde (DMAC) and cyanoacrylate (CN), our team demonstrated effective fluorescence staining of cyano-treated fingermarks using DMAC/OA misting or DMAC/2PE misting, and one-step fluorescence detection of latent fingermarks without cyanoacrylate treatment using DMAC/OA/CN misting or DMAC/MD/CN misting. Fingermark fluorescence was efficiently observed by excitation with a blue LED light (max. wavelength 470 nm) equipped with an interference filter and passing through a 520 nm long-pass filter. We successfully obtained fluorescent images from fingermarks on several substrate materials using the developed misting method.     

Determining the order of deposition of natural latent fingerprints and laser printed ink using chemical mapping with secondary ion mass spectrometry

Time-of-flight secondary ion mass spectrometry (ToF-SIMS) chemical mapping was used to investigate the order of deposition of natural latent fingerprints and laser printed ink on paper. This feasibility study shows that sodium, potassium and C₃H₅ positive ions were particularly abundant endogenous components of the natural fingerprints and also present in the paper examined, but were mostly absent in the laser printed ink. Mapping of these ions enables the observation of friction ridges from latent prints on the ink surface, only when a fingerprint was deposited above the layer of ink. As a demonstration of proof of concept, blind testing of 21 samples from three donors resulted in a 100% success rate. The sensitivity of this technique was investigated within this trial through the examination of up to fifth depletion fingerprints and ageing of up to 28 days. Migration of fingerprint and paper components to the ink surface, although observed with increased ageing time, was not found to compromise determination of the deposition sequence.     

Fingerprint reagents with dual action: color and fluorescence

We define "dual fingerprint reagents" as chemical formulations that produce with latent fingerprints in one stage impressions that are both colored and fluorescent. Solutions containing ninhydrin and group IIb metal salts appear to be true dual reagents. Application of these formulations to latent fingerprints on paper is as efficient as the two-step process beginning with ninhydrin and followed by treatment with metal salt. In the color mode, fingerprint detectability with the two ninhydrin-metal salt reagents (one with zinc chloride and the other with cadmium chloride) is comparable with that of ninhydrin itself, in spite of the difference in color. The sensitivity is significantly higher in the fluorescence mode. To view the latent impressions the exhibits are treated with ninhydrin-metal salt reagents and observed under white light illumination and under fluorescence conditions. Cooling to liquid nitrogen temperature enhances the fluorescence considerably. In the shorter wavelength domain, ninhydrin-metal salt reagents exhibit higher sensitivity than the recently reported dual reagent, genipin. The latter is advantageous, however, in the longer wavelength domain, on paper items with strong self-fluorescence, such as brown wrapping paper or paper printed with fluorescent ink. Upon reduction of the ninhydrin concentration 10-fold, ninhydrin-metal salt formulations become purely fluorogenic reagents; no color is noticed but the fluorescence is as intense as with concentrated solutions. Working at lower concentrations is an advantage from ecological and economical viewpoints.     

Raman spectroscopy and laser desorption mass spectrometry for minimal destructive forensic analysis of black and color inkjet printed documents

Inkjet ink analysis is the best way to discriminate between printed documents, or even though more difficult, to connect an inkjet printed document with a brand or model of printers. Raman spectroscopy and laser desorption mass spectrometry (LDMS) have been demonstrated as powerful tools for dyes and pigments analysis, which are ink components. The aim of this work is to evaluate the aforementioned techniques for inkjet inks analysis in terms of discriminating power, information quality, and nondestructive capability. So, we investigated 10 different inkjet ink cartridges (primary colors and black), 7 from the HP manufacturer and one each from Epson, Canon and Lexmark. This paper demonstrates the capabilities of three methods: Raman spectroscopy, LDMS and MALDI-MS. Raman spectroscopy, as it is preferable to try the nondestructive approach first, is successfully adapted to the analysis of color printed documents in most cases. For analysis of color inkjet inks by LDMS, we show that a MALDI matrix (9-aminoacridine, 9AA) is needed to desorb and to ionize dyes from most inkjet inks (except Epson inks). Therefore, a method was developed to apply the 9AA MALDI matrix directly onto the piece of paper while avoiding analyte spreading. The obtained mass spectra are very discriminating and lead to information about ink additives and paper compositions. Discrimination of black inkjet printed documents is more difficult because of the common use of carbon black as the principal pigment. We show for the first time the possibility to discriminate between two black-printed documents coming from different, as well as from the same, manufacturers. Mass spectra recorded from black inks in positive ion mode LDMS detect polyethylene glycol polymers which have characteristic mass distributions and end groups. Moreover, software has been developed for rapid and objective comparison of the low mass range of these positive mode LDMS spectra which have characteristic unknown peaks.     

Determination of the Chronological Order of a Laser Printing and Gel Pen Writing Without any Crossing Strokes

Laser printers and writing instruments are being exploited by the forgers to produce fabricated documents. They often produce such documents by appending genuine signature on a blank sheet and later printing on it. Often these fabricated documents do not contain intersection of strokes and may pose a difficulty to forensic document examiners in analyzing cases related to such documents. Keeping in mind the limited research work done on nonintersecting strokes, the present study has been conducted with an aim to determine the sequence of nonintersecting strokes of gel pens and laser printers. Three hundred samples of nonintersecting strokes of gel pen ink and laser printing were prepared. Of these 300, 150 had laser-printed text below the gel pen strokes and the remaining 150 were prepared with gel pen stokes below the laser-printed text. The samples have been analyzed using Nikon SMZ 800N stereomicroscope. Three micro-conformation features, that is, pattern of toner distribution, ink distribution, and fiber distribution have been observed in the samples. The results demonstrate the successful establishment of sequence of nonintersecting strokes in case of gel pen and laser-printed documents by the determination of micro-conformation features.     

An Examination of the Sequence of Intersecting Lines using Microspectrophotometry

The potential of microspectrophotometry as a technique to determine the sequence of intersecting lines was examined. The technique was used to determine the sequence of heterogeneous line intersections produced using inkpad, stamp‐pad ink and ballpoint pens, gel pens, fountain pens, laser and ink‐jet printers. The study was carried out with an assumption that the peak characteristics of spectra from the point of intersection should correspond to the peak characteristics of pure ink which was executed later. According to spectral reflectance curves, microspectrophotometry was possible to determine whether the ink was above or below the inkpad/stamp‐pad ink seals. In blind testing, microspectrophotometry technique results were directly compared to those obtained by five experienced forensic document examiners using optical microscopy regularly employed in casework. As the results obtained from the study were positive, microspectrophotometry technique was found to be very successful in determining the sequence of heterogeneous line intersections under some conditions.     

Application of Video Spectral Comparator (absorption spectra) for establishing the chronological order of intersecting printed strokes and writing pen strokes

The sequence of intersecting strokes of laser printers (black, blue, red and green) and typewriter ink (black) with the strokes of gel pen ink, ballpoint pen ink and fountain pen ink (black, blue, red and green) has been determined by studying their absorption spectra. The absorption spectra have been generated for each of the two pure inks (i.e. A and B) and points of their intersections (i.e. A over B and B over A) by using Video Spectral Comparator (VSC-2000-HR). The study was carried out with an assumption that the peak characteristics of spectra from the point of intersection should correspond to the peak characteristics of pure ink which was executed later. It was observed that the absorption spectrum of intersection corresponds with either the laser printer or the typewriter ink stroke, whether these strokes were executed earlier or later than the writing instrument strokes. As the results obtained from the study were negative, the FDEs are advised against the practice of this technique in the examination of the sequence of intersecting strokes for these specified inks.     

An examination of the sequence of intersecting lines using attenuated total reflectance-Fourier transform infrared spectral imaging

In this study, the potential of attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectral imaging as a technique to determine the sequence of line crossings was examined. The technique was successful in determining the sequence of heterogeneous line intersections produced using ballpoint pens and laser printers. By imaging at characteristic frequencies, it was possible to form spectral images showing the spatial distribution of the materials. By examining the spectral images from the inks, it was possible to determine whether the ink was above or below the toner. In blind testing, ATR-FTIR spectral imaging results were directly compared to those obtained by eight experienced forensic document examiners using methods regularly employed in casework. ATR-FTIR spectral imaging was shown to achieve a 100% success rate in the blind tests, whereas some incorrect sequence determinations were made by the forensic document examiners when using traditional techniques. The technique was unable to image ink-jet printing, gel pens, roller ball pens, and felt-tip pens, and was also unable to determine the sequence of intersecting ballpoint pen lines.