裂解气相色谱-质谱法和红外光谱法对红色汽车油漆的比较分析

目的应用裂解气相色谱-质谱法（Py-GC/MS）和红外光谱法（IR）鉴别3种红色汽车油漆,通过二者的比较,考察Py-GC/MS法在微量物证油漆鉴定中的适用性。方法取适量固体样品直接检测。IR检测条件：红外显微镜,透射模式,光阑尺寸100μm×100μm,检测范围为4000-675cm-1。Py-GC/MS检测条件：裂解温度：550℃,裂解时间：0.20min。HP-5MS色谱柱,分流比80∶1;升温程序：起始温度为40℃,保持1 min,然后以8℃/min升至300℃,保持1 min。质谱采用EI源,扫描范围：29~350 amu。结果 3种红色汽车油漆的红外光谱、裂解图谱均能相互区分。通过裂解产物,能获得更多油漆主要成膜物质的成分信息。结论在样品量许可的条件下,应在红外光谱的检测基础上,进一步使用裂解气相色谱-质谱方法来对汽车油漆进行检测,通过互相验证,获得更准确、可靠的油漆鉴定结果。     

Discriminating red spray paints by optical microscopy, Fourier transform infrared spectroscopy and X-ray fluorescence

Red spray paints from different European suppliers were characterised to determine the discriminating power of a sequence of analysing techniques. A total of 51 red spray paints were analysed with the help of three techniques: (1) optical microscopy, (2) Fourier transform infrared spectrometry and (3) X-ray fluorescence. Infrared spectra were classified according to binder type, filler and pigment composition and a searchable spectral library was created. Due to the difference in the elemental composition of spray paints, a further discrimination was possible. The microscopic analysis was not taken into consideration for classification purposes. The structure of the substrate under a paint coating strongly affects the surface characteristics of this spray paint. Together with the spectral library, a database of information of spray paints was build.     

Direct identification of various copper phthalocyanine pigments in automotive paints and paint smears by laser desorption ionization mass spectrometry

Direct identification of copper phthalocyanine (CuPc) and chlorinated CuPcs in paints for discrimination between blue automobile paints by means of laser desorption mass spectrometry (LDMS) in the absence of a matrix is reported. The models consisted of eight commercially available CuPc pigments applied to a piece of plain white coating paper. The relationship between the peak intensity at m/z 575 of the CuPc, the number of pulsed laser shots, and laser power was compared to optimize laser abrasion. LDMS analysis of the model paints demonstrated that all characteristic components of the CuPc pigments in the paint films were in good agreement with those in the powder pigments. Further, the chlorinated CuPcs in the paint films could be distinguished. A quantity of 42 blue paint films, representing the paints used for painting Japanese domestic trucks, was examined by LDMS analysis. Results indicate that the paints can be classified into four categories based on the chlorinated CuPc components of the paints. Therefore, LDMS spectra of CuPc pigments would be useful for the identification of paints in forensic investigations. Herein, we report the successful identification of the CuPcs in a paint smear on the frame of a bicycle damaged in a hit-and-run accident, using the LDMS spectra.     

近红外显微分光光度法鉴别油漆的研究

本文借助显微分光光度计系统在近红外区域对几种“色觉”相似的油漆样品进行了光谱学分析。结果表明，近红外显微分光光度计能有效地鉴别颜色相似的油漆。该法准确、可靠，且不破坏检材．对实际检案有重要意义。     

The Evidentiary Significance of Automotive Paint from the Northeast: A Study of Red Paint

This population study was conducted to assess the frequency of physical, microscopical, and chemical properties of automotive paint chips. Population studies of trace evidence provide valuable analytical data for criminalists to assess evidentiary significance. Two‐hundred automotive paint chips were collected from auto body shops from the Northeastern United States. All samples were analyzed using stereomicroscopy, brightfield, and polarized light microscopy. Red paints were targeted for further analysis using a sequence of modern instrumental techniques commonly used by forensic paint examiners: Fourier‐transform infrared (FT‐IR), Raman, and ultraviolet–visible (UV–Vis) microspectroscopy. The discrimination potential of each analytical method was evaluated by inter‐comparing the paint samples. Results demonstrated that macroscopic and microscopic properties were able to differentiate 99.995% of the population (one undifferentiated pair out of 19,900). When combined with either FT‐IR or UV–Vis microspectroscopy, all paints were differentiated. The results of this research lead to the conclusion that one would not expect to encounter two indistinguishable paint chips originating from different sources during the investigation of a single event.     

The kinetics of colour change in textiles and fibres treated with detergent solutions: Part II — Spectrophotometric measurements

The aim of this study was to assess colour variations that occur in several types of textiles and their constituent fibres, resulting from the long-term influence of various laundry detergents. A 14-day experiment was conducted using blue, red and grey/black cotton, wool, acrylic and polyester textiles. The spectrophotometric measurement of colour changes in fabric samples and test solutions, as well as the microspectrophotometric analysis of colour changes in single fibres were described. An evaluation of the observed colour changes from a forensic fibre analysis expert's point of view, as well as that of an average user/consumer of the textiles and laundry detergents is also provided.     

Using Paint to Investigate Fires: An ATR‐IR Study of the Degradation of Paint Samples Upon Heating

Fire investigation is a challenging area for the forensic investigator. The aim of this work was to use spectral changes to paint samples to estimate the temperatures to which a paint has been heated. Five paint samples (one clay paint, two car paints, one metallic paint, and one matt emulsion) have been fully characterized by a combination of attenuated total reflectance Fourier transform infrared (ATR‐IR), Raman, X‐ray fluorescence spectroscopy and powder X‐ray diffraction. The thermal decomposition of these paints has been investigated by means of ATR‐IR and thermal gravimetric analysis. Clear temperature markers are observed in the ATR‐IR spectra namely: loss of ν(C = O) band, >300°C; appearance of water bands on cooling, >500°C; alterations to ν(Si–O) bands due to dehydration of silicate clays, >700°C; diminution of ν(CO₃) and δ(CO₃) modes of CaCO₃, >950°C. We suggest the possible use of portable ATR‐IR for nondestructive, in situ analysis of paints.     

Color analysis of apparently achromatic automotive paints by visible microspectrophotometry

Chromatic secondary pigments are utilized in achromatic automotive paints to create unique paint systems. These pigments may not be observable in reflected light; however, utilizing visible microspectrophotometry (MSP) discriminating data may be gathered. This study analyzed 160 apparently achromatic automotive paints via this technique for spectral evidence of secondary pigmentation. These results were compared with visual observations made via polarizing light microscopy. Positive spectral results were attained in approximately 25% of the black and gray/silver topcoat sample sets, whereas the white topcoat and gray undercoat set yielded no probative spectral data. The black sample set did yield several samples that produced spectral evidence of pigmentation when no visual chromatic data was observed. The results of this study suggest that paint analysis schemes should incorporate visible MSP for apparently achromatic black and gray/silver paint samples.     

Survey of crowbar and household paints in burglary cases-population studies, transfer and interpretation

Experimental data useful for the interpretation of paint evidence recovered during burglary cases were obtained. A population study was carried out on 41 blue crowbars seized on suspects in Switzerland and 37 blue paints traces found at burglary scenes. Paint traces were also searched on the blades of 207 crowbars seized by the police in Switzerland and 24 white traces were analysed: these paints were analysed using infrared spectroscopy (FTIR) in order to estimate relative frequencies of each paint type. Simulated contacts were carried out between crowbars and painted wood in order to study the phenomenon of transfer and to evaluate the amount of paint transferred: a total of 198 simulations were carried out including individual, successive and cross transfer. The paint properties such as the chemical composition and its age influenced the amount of paint transferred. Cross transfer from the tool paint to the wood and vice versa was regularly observed. Moreover, secondary transfer of paint coming from the preceding wooden surfaces was also systematically observed: this could establish links between several burglary scenes and a suspected tool. A scenario of a burglary case involving the cross transfer between tool and household paints is proposed as a numerical example: the evaluation of such case was formalised using likelihood ratios based on the experimental data obtained.     

Characterization and differentiation of aluminum powders used in improvised explosive devices – Part 1: Proof of concept of the utility of particle micromorphometry

Aluminum (Al) powders are commonly used in improvised explosive devices as metallic fuels, a component of explosive mixtures. These powders can be obtained readily from industrial‐scale and consumer products, and produced using unsophisticated “kitchen chemistry” techniques. This research demonstrates the potential of automated particle micromorphometry for comparisons between known source and questioned Al powders recovered from IEDs, as well as for insight into the method of Al powder manufacture. Al powder samples were obtained from legitimate manufacturers, and 56 samples were produced “in‐house” from Al‐containing spray paints and ball‐milled Al foils. Transmitted light microscope images of Al powder particles were acquired using an automated stage with automated z‐focus; 17 size and shape parameters were measured for all particles. Approximately 37,000–2,500,000 particles/sample were analyzed using an open‐source statistical package with customized code. Dimensionality reduction was required for processing the large datasets: eight of the 17 measured variables were selected based on inspection of the correlation matrix. Data from four subsamples from each of the 56 samples produced using “in‐house” methods were analyzed using ANOVA to assess the within‐ and between‐sample variation. High within‐sample variation was noted; however, ANOVA and post‐hoc Tukey's honestly significant difference (HSD) tests demonstrated that the between‐sample variation was substantially larger than the within‐sample variation. Each sample could be differentiated from all other samples in the test set. Future experiments will focus on ways to reduce the within‐sample variation, and additional statistical and microanalytical methods to classify sources and confidently constrain the method of Al powder manufacture.     

Discrimination of 1990s original automotive paint systems: a collaborative study of black nonmetallic base coat/clear coat finishes using infrared spectroscopy

The 1990s saw the introduction of significantly new types of paint binder chemistries into the automotive finish coat market. Considering the pronounced changes in the binders that can now be found in automotive paints and their potential use in a wide variety of finishes worldwide, the Paint Subgroup of the Scientific Working Group for Materials (SWGMAT) initiated a validation study to investigate the ability of commonly accepted methods of forensic paint examination to differentiate between these newer types of paints. Nine automotive paint systems typical of original equipment applications were acquired from General Motors Corporation in 1992. They consisted of steel panels coated with typical electrocoat primers and/or primer surfacers followed by a black nonmetallic base coat and clear coat. The primary purpose of this study was to evaluate the discrimination power of common forensic techniques when applied to the newer generation original automotive finishes. The second purpose was to evaluate interlaboratory reproducibility of automotive paint spectra collected on a variety of Fourier transform infrared (FT-IR) spectrometers and accessories normally used for forensic paint examinations. The results demonstrate that infrared spectroscopy is an effective tool for discriminating between the major automotive paint manufacturers' formulation types which are currently used in original finishes. Furthermore, and equally important, the results illustrate that the mid-infrared spectra of these finishes are generally quite reproducible even when comparing data from different laboratories, commercial FT-IR instruments, and accessories in a "real world," mostly uncontrolled, environment.     

Recovery of Trace DNA on Clothing: A Comparison of Mini‐tape Lifting and Three Other Forensic Evidence Collection Techniques

Trace DNA is often found in forensic science investigations. Experience has shown that it is difficult to retrieve a DNA profile when trace DNA is collected from clothing. The aim of this study was to compare four different DNA collection techniques on six different types of clothing in order to determine the best trace DNA recovery method. The classical stain recovery technique using a wet cotton swab was tested against dry swabbing, scraping and a new method, referred to as the mini‐tape lifting technique. Physical contact was simulated with three different “perpetrators” on 18 machine‐washed garments. DNA was collected with the four different DNA recovery methods and subjected to standard PCR‐based DNA profiling. The comparison of STR results showed best results for the mini‐tape lifting and scraping methods independent of the type of clothing. The new mini‐tape lifting technique proved to be an easy and reliable DNA collection method for textiles.     

A Two‐Level Model for Evidence Evaluation in the Presence of Zeros*

Abstract: Likelihood ratios (LRs) provide a natural way of computing the value of evidence under competing propositions. We propose LR models for classification and comparison that extend the ideas of Aitken, Zadora, and Lucy and Aitken and Lucy to include consideration of zeros. Instead of substituting zeros by a small value, we view the presence of zeros as informative and model it using Bernoulli distributions. The proposed models are used for evaluation of forensic glass (comparison and classification problem) and paint data (comparison problem). Two hundred and sixty‐four glass samples were analyzed by scanning electron microscopy, coupled with an energy dispersive X‐ray spectrometer method and 36 acrylic topcoat paint samples by pyrolysis gas chromatography hyphened with mass spectrometer method. The proposed LR model gave very satisfactory results for the glass comparison problem and for most of the classification tasks for glass. Results of comparison of paints were also highly satisfactory, with only 3.0% false positive answers and 2.8% false negative answers.     

A method for enhancing gunshot residue patterns on dark and multicolored fabrics compared with the modified Griess test

In using infrared or infrared-enhanced photography to examine gunshot residue (GSR) on dark-colored clothing, the GSR particles are microscopically examined directly on the fabric followed by the modified Griess test (MGT) for nitrites. In conducting the MGT, the GSR is transferred to treated photographic paper for visualization. A positive reaction yields an orange color on specially treated photographic paper. The examiner also evaluates the size of the powder pattern based on the distribution of nitrite reaction sites or density. A false-positive reaction can occur using the MGT due to contaminants or dyes that produce an orange cloud reaction as well. A method for enhancing visualization of the pattern produced by burned and partially unburned powder is by treatment of the fabric with a solution of sodium hypochlorite. In order to evaluate the results of sodium hypochlorite treatment for GSR visualization, the MGT was used as a reference pattern. Enhancing GSR patterns on dark or multicolored clothing was performed by treating the fabric with an application of 5.25% solution of sodium hypochlorite. Bleaching the dyes in the fabric enhances visualization of the GSR pattern by eliminating the background color. Some dyes are not affected by sodium hypochlorite; therefore, bleaching may not enhance the GSR patterns in some fabrics. Sodium hypochlorite provides the investigator with a method for enhancing GSR patterns directly on the fabric. However, this study is not intended to act as a substitute for the MGT or Sodium Rhodizonate test.     

Identification of organic pigments in automotive coatings using laser desorption mass spectrometry

When one looks at an automotive coating, one sees color due to pigments. Modern organic pigments, with high molar absorptivities, may be only minor components of the mixture. Laser desorption mass spectrometry (LDMS) has been shown to be a useful tool for the analysis of colorants such as pen ink dyes. Here, LDMS is used to determine its utility for the identification of pigments, in simple media and in more complex paints. Small paint chips can be introduced into the LDMS instrument, and when an ultraviolet laser is focused on a portion of a chip, ions representative of the pigment(s) are selectively formed. Some pigments such as quinacridones and copper phthalocyanine are very stable and are desorbed and ionized intact. In contrast, benzimidazolones, which contain some single-skeletal bonds, form fragment ions. This method proves to be sensitive and convenient, as no sample preparation is required. The presence of inorganic pigments in addition to modern organic pigments can be determined, and pigments can be directly identified in actual automotive paint chip samples.     

The evaluation of human hand odor volatiles on various textiles: a comparison between contact and noncontact sampling methods

The focus of this study is to compare contact and noncontact human scent collection procedures across an array of textiles (cotton, rayon, polyester, and wool) to determine an optimized collection method for human scent evidence. Six subjects were sampled in triplicate for each textile and collection mode, and the samples were then analyzed through headspace solid-phase micro-extraction in combination with gas chromatography/mass spectrometry (SPME-GC/MS). Contact sampling with cotton material has been shown to be the collection method that yielded the greatest number of volatile compounds and the highest scent mass amounts. Through Spearman rank correlations, it was shown that an individual's scent profile is more reproducible within samples collected on the same textile type than between different materials. Furthermore, contact sampling with cotton fabric demonstrated the greatest reproducibility producing the lowest amount of type I and type II errors with 90.85% of the samples distinguished at the 0.9 match/no match threshold.     

Impact Spatter Bloodstain Patterns on Textiles

There are few reports of studies of impact spatter on textiles even though bloodstained textiles are found at many violent scenes. Impact spatter was deposited at 90° impact angle onto three knit fabrics of different yarn sizes and on paper. The resulting stain areas and number of stains were measured using ImageJ and compared with stains on paper using one‐factor ANOVA. The number of stains observed and their areas on the knit fabrics decreased as the yarn size increased. It was also found that blood that deposited on the fabric wicked only in the direction of the fibers at that location within the fabric which led to distorted stain shapes. Fewer observed impact spatter stains were found on cotton jersey knits for fabrics made with larger yarns than on paper. As the yarn size became smaller, the number of stains became the same as on paper.     

A versatile technique for the investigation of gunshot residue patterns on fabrics and other surfaces: m-XRF

With heavy-metal-free ammunitions becoming more and more popular, it is necessary to find methods to visualize patterns of those elements in gunshot residues (GSRs) that are not accessible by chemographic coloring tests. The recently introduced millimeter-X-ray fluorescence analysis (m-XRF) spectrometer Spectro Midex M offers an easy way to record mappings of GSRs containing such elements in order to determine shooting distances as well as the general composition of these particles. A motorized stage enables samples of a maximum size of 20 x 20 cm to be investigated, like fabric, clothes, adhesive tapes (Filmolux films), and polyvinylalcohol gloves of shooter's hands. Human tissues can be measured using a Peltier-cooled specimen holder that is mounted onto the stage. As the spot size of the exiting X-rays lies in the millimeter range, which is adequate for the assessment of the residue patterns for shooting distance determination, a significant reduction in measurement time is achieved compared with mu-XRF methods. Test shots with heavy-metal-free ammunitions were performed on different target materials, like pork skin and fabric, and the elemental distributions of Ti, K, and Ga were determined. In order to show the capability of the spectrometer for conventional lead ammunitions as well, a shot series of 5-100 cm shooting distance and an adhesive tape of a shooter's hand were investigated analogously. A comparison of several methods applied in GSR investigation shows the advantages of the m-XRF method.     

Paint and tape: collection and storage of microtraces of paint in adhesive tape

The collection and preservation of microtrace evidence with the aid of an adhesive tape is a method of choice in forensic science. This technique is rapid and easy and allows the concentration of microtraces on a carrier, which facilitates further investigations in the laboratory. Adhesive tapes are currently used to secure microtraces of fibers and glass, but hardly for traces of automotive paint and other lacquers for fear of interference with the analysis of binders. A collection of automotive paint consisting of original and repair lacquers collected by tape has been evaluated. After various times of storage within the tape, these samples were compared with untreated references by microscope FT-IR and microspectrophotometry (MSP). Another set of paints was collected in 1984, stored within the tape until 1995, and examined the same way. About 170 layers of lacquer with various types of binder were examined. With the exception of one clear lacquer no difference between treated samples and references was detected. This small difference observed could be correlated to the exposure to xylene (extractant) and was not caused by the storage within the adhesive tape.     

Classification Improvements in Automated Gunshot Residue (GSR) Scans

Classification of particles as gunshot residues (GSRs) is conducted using a semiautomatic approach in which the system first classifies particles based on an automatic elemental analysis, and then, examiners manually analyze particles having compositions which are characteristic of or consistent with GSRs. Analyzing all the particles in the second stage is time consuming with many particles classified by the initial automated system as being potentially GSRs excluded as such by the forensic examiner. In this paper, a new algorithm is developed to improve the initial classification step. The algorithm is based on a binary tree that was trained on almost 16,000 particles from 43 stubs used to sample hands of suspects. The classification algorithm was tested on 5,900 particles from 23 independent stubs and performed very well in terms of false positive and false negative rates. A routine use of the new algorithm can reduce significantly the analysis time of GSRs.