Calcium and Phosphorus Detection Using Benchtop Versus Handheld X‐ray Fluorescence Spectrometers

Elemental analysis of calcium (Ca) and phosphorus (P) has been shown to be useful in differentiating skeletal and nonskeletal material. X‐ray fluorescence spectrometry (XRF) is an attractive, nondestructive technique for forensic anthropologists, and the development of portable XRF instrumentation is promising for field applications. This study examines the performance of handheld XRF instrumentation operated in air compared to a traditional benchtop XRF device that has the ability to control the analysis atmosphere. Both instruments can be used to effectively distinguish skeletal from nonskeletal remains. However, as the measurement atmosphere affects detection levels for calcium and phosphorus, Ca/P ratios obtained from the instruments and analysis conditions were found to differ significantly, with analyses conducted in air showing significantly lower phosphorus detection. Consequently, comparison of Ca/P ratios to conclude skeletal versus nonskeletal origin must be based on data collected under similar analysis conditions.     

Use of scanning electron microscopy and energy dispersive X-ray analysis (SEM-EDXA) in identification of foreign material on bullets

The authors report two cases in which examination of foreign material embedded in or adherent to bullets provided critical information in the reconstruction of a crime scene. Analysis of small particles by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDXA) can be accomplished without destruction or injury of the particles. In one case, the detection and identification of mineral fragments embedded near the nose of a bullet provided conclusive evidence that the bullet had ricocheted from a fireplace before striking the victim. In the second case, analysis of particles from two bullets identified them as them as bone fragments, thus proving which shots fired from a police officer's gun had killed a suspected burglar. SEM-EDXA has not been widely used to identify such material on bullets, but should be considered a potentially powerful tool in forensic science.     

Lung embolism with liquid silicone

A lung embolism was reported in a case involving death following repeated injections of liquid silicone for aesthetic reasons. The liquid extracted from the sites of injection was identified as methylsilicone using infrared spectrophotometry, and the presence of silicone in vacuoles in the lung was verified by scanning electron microscopy with energy dispersive X-ray analysis (EDXA). A study has been carried out with rats after intravenous and subcutaneous injections of methylsilicone.     

Political Embeddedness and its Impact on Chinese Lawyers’ Practices in Criminal Defense Cases

Based on survey data of 348 lawyers in Fujian, this study empirically tests how lawyers' political embeddedness (i.e., lawyers' bureaucratic, instrumental, and/or affective ties to the courts and prosecutors) has impacted upon their defense practices in criminal trials and their pursuit of liberal values. Our data reveal that politically embedded lawyers report more (not fewer) difficulties in practice (e.g., in requesting witness testimony in court, requesting new evidence, and requesting new evaluations and investigations of the case). Clients are more satisfied with representation by politically non-embedded lawyers than lawyers who are embedded. Using statistical evidence, this paper analyzes potential reasons and draws out the implications.     

中介素（IMD）对大鼠心肌细胞缺氧-复氧损伤的作用

目的探讨中介素（IMD）对大鼠体外培养心肌细胞缺氧-复氧损伤的作用。方法用大鼠H9c2心肌细胞株制作实验模型,样本分为对照组、缺氧-复氧组（缺氧1h、复氧30min）、IMD组（缺氧-复氧前30min加入10-7mol/L IMD）。采用MTT比色法检测心肌细胞活力;透射电镜观察细胞超微结构;激光共聚焦显微镜观察并测定细胞内钙离子浓度;流式细胞术测定细胞凋亡率。结果与对照组比较,缺氧-复氧组和IMD组细胞存活率显著降低,而IMD处理组明显升高细胞存活率（P〈0.01）;在形态学上,IMD预处理可明显减轻缺氧-复氧对大鼠心肌细胞的损伤;缺氧-复氧组细胞[Ca2＋]i荧光强度和细胞凋亡率比对照组显著升高,IMD预处理可明显降低上述升高的比率（P〈0.01）。结论 IMD对大鼠心肌细胞缺氧-复氧损伤有一定保护作用,提高心肌细胞存活率、减轻心肌细胞钙超载和抑制凋亡是其作用途径。     

The use of SEM/EDS analysis to distinguish dental and osseus tissue from other materials

With increasing frequency, relatively small, fragmentary evidence thought to be osseous or dental tissue of human origin is submitted to the forensic laboratory for DNA analysis with the request for positive identification. Prior to performing DNA analysis, however, it is prudent to first perform a presumptive test or "screen" to determine whether the questioned material may be eliminated from further consideration. When material is shown not to be consistent with bone/teeth, DNA testing is not performed. When such determinations cannot be made from gross morphological features, elemental analysis can be indicative. This presumptive test is made possible by applying scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS) in conjunction with an X-ray spectral database recently developed by the FBI laboratory. This database includes spectra for many different materials including known examples of bone and tooth from many different contexts and representing the full range of taphonomic conditions. Results of SEM/EDS analysis of evidence can be compared to these standards to determine if they are consistent with bone and/or tooth and, if not, then what the material might represent. Analysis suggests that although the proportions and amounts of calcium and phosphorus are particularly important in differentiating bone and tooth from other materials, other minor differences in spectral profile can also provide significant discrimination. Analysis enables bone and tooth to be successfully distinguished from other materials in most cases. Exceptions appear to be ivory, mineral apatite, and perhaps some types of corals.     

Identification of Crystals Forming on Porcine Articular Cartilage: A New Method for the Estimation of the Postmortem Interval

Articular cartilage was examined to determine its decomposition sequence and its potential for assessing the postmortem interval. Scanning electron microscopy of articular cartilage from buried porcine trotters showed the presence of microcrystals on the synovial surface. These orthorhombic pyramidal or “coffin”‐shaped crystals, appeared at 3 weeks (22 days) after interment and disappeared after 6 weeks. The disappearance of these crystals was linked to decompositional changes to the integrity of the synovial joint. The formation and disappearance of these crystals was associated with a pH change at the cartilage surface. Scanning electron microscopy–energy‐dispersive X‐ray (SEM‐EDX) analysis showed that the five main elements contained within these crystals were carbon, nitrogen, oxygen, magnesium, and phosphorous. Such elemental analysis suggested the crystals may be struvite (MgNH₄PO₄6(H₂O)). Bacteria cultured from the cartilage synovial surface produced struvite crystals when grown in suitable media and were identified by DNA analysis to be Comamonas sp.     

家兔死后玻璃体液离子浓度检测的微量重复取样法

目的探讨微量重复取样法对兔玻璃体液样本离子浓度或元素含量检测的可行性。方法28只家兔分为3组:Ⅰ组:死后12h一次取出所有玻璃体液;Ⅱ组:死后12h微量取样50μl,连续取15次;Ⅲ组:死后120h微量取样50μl,连续取15次。分别检测样本中Ca2+、C l-、K+、Na+和磷元素的含量,并对所得数据进行统计分析。结果Ⅰ、Ⅱ、Ⅲ组左、右眼的Ca2+均数分别为1.956和2.068,1.942和1.948,2.071和2.045;C l-为111.520和121.240,116.744和117.022,106.322和106.767;K+为13.016和13.900,11.230和11.144,35.411和34.828;Na+为127.200和141.880,133.872和134.566,111.511和110.647;磷元素为0.556和0.744,0.284和0.280,5.585和5.597。3组双眼上述5种成分含量经配对t检验,其P值范围分别为0.2753~1.2365,0.1627~1.6596,0.1520~1.3446,0.2386~1.0892和0.0575~0.8195;Ⅱ、Ⅲ组的重复取样检测经方差分析,其P值为0.9433和0.8638,两组总体重复取样检测的方差分析,P值为0.8772。结论微量重复取样法对兔玻璃体液样本离子或元素含量的检测无实际影响。     

微量纤维的横截面样品制备及检验方法研究

目的建立一种纤维横截面样品的制样和检验方法,实现对微量和单根纤维的横截面检验。方法以速干胶为包埋剂,细塑料管为模具,包埋体用切片机切片,制成纤维的横截面样品,在环境扫描电镜下检测纤维的横截面形态。结果制成的纤维横截面样品分散性好,截面挤压变形小,包埋体与截面边界明确,形态特征清晰。结论该方法操作简单、快速,适合微量或单根纤维物证的横截面检验。     

Effect of evaporation and matrix interferences on the association of simulated ignitable liquid residues to the corresponding liquid standard

Identification of an ignitable liquid in fire debris evidence can be complicated due to evaporation of the liquid, matrix interferences, and thermal degradation of both the liquid and the matrix. In this research, liquids extracted from simulated fire debris were compared to the original liquid using multivariate statistical procedures. Neat and evaporated gasoline and kerosene standards were spiked onto nylon carpet, which was subsequently burned. The ignitable liquid residues were extracted using a passive headspace procedure and analyzed by gas chromatography-mass spectrometry. Pearson product moment correlation coefficients, hierarchical cluster analysis, and principal components analysis were used to compare the liquids extracted from the carpet to the corresponding neat liquid. For each procedure, association of the extracts according to liquid type was possible, albeit not necessarily to the specific evaporation level. Of the three procedures investigated, principal components analysis offered the most promise since contributions from matrix interferences were essentially eliminated.     

二醋吗啡对大鼠心肌细胞游离Ca^2＋浓度的作用

目的观察二醋吗啡对心肌细胞内游离Ca2 浓度的作用。方法取自1～3d的SD大鼠培养的心肌细胞,用荧光探针Fluo-3/AM负载心肌细胞,不同浓度及不同剂量的二醋吗啡作用心肌细胞,激光共聚焦显微镜下检测Ca2 的变化。结果不同剂量及浓度的二醋吗啡对心肌细胞内游离Ca2 浓度有不同作用,一定浓度的二醋吗啡使心肌细胞内游离Ca2 浓度呈剂量依赖性的升高、短时间内心肌细胞[Ca2 ]i荧光强度增强,并产生[Ca2 ]i峰。结论探索出二醋吗啡导致心肌细胞内Ca2 变化的有效浓度,为进一步深入研究打下了基础。     

Validation of X-ray fluorescence spectrometry for determining osseous or dental origin of unknown material

Forensic anthropological examinations typically involve the analysis of human skeletal remains, but in cases where samples are very small and/or physically compromised, it may first be necessary to determine whether the material is even osseous or dental in origin. X-ray fluorescence spectrometry (XRF) is a technique that reveals the elemental composition of materials and is hypothesized to have utility in such cases. XRF analysis was conducted on a variety of tissues and materials in unaltered and altered (damaged) states. With few exceptions, osseous and dental tissues in unaltered and altered conditions contained characteristic levels of calcium and phosphorus, while other materials did not. Materials could be accurately identified as osseous or dental in origin based on the calcium and phosphorus levels identified by XRF, and we therefore conclude that XRF analysis is a valid and effective means of determining osseous or dental origin of unknown material.     

Forensic Analysis of Explosives Using Isotope Ratio Mass Spectrometry (IRMS)—Part 1: Instrument Validation of the DELTAplusXP IRMS for Bulk Nitrogen Isotope Ratio Measurements

Abstract: A significant amount of research has been conducted into the use of stable isotopes to assist in determining the origin of various materials. The research conducted in the forensic field shows the potential of isotope ratio mass spectrometry (IRMS) to provide a level of discrimination not achievable utilizing traditional forensic techniques. Despite the research there have been few, if any, publications addressing the validation and measurement uncertainty of the technique for forensic applications. This study, the first in a planned series, presents validation data for the measurement of bulk nitrogen isotope ratios in ammonium nitrate (AN) using the DELTA^plusXP (Thermo Finnigan) IRMS instrument equipped with a ConFlo III interface and FlashEA? 1112 elemental analyzer (EA). Appropriate laboratory standards, analytical methods and correction calculations were developed and evaluated. A validation protocol was developed in line with the guidelines provided by the National Association of Testing Authorities, Australia (NATA). Performance characteristics including: accuracy, precision/repeatability, reproducibility/ruggedness, robustness, linear range, and measurement uncertainty were evaluated for the measurement of nitrogen isotope ratios in AN. AN (99.5%) and ammonium thiocyanate (99.99+%) were determined to be the most suitable laboratory standards and were calibrated against international standards (certified reference materials). All performance characteristics were within an acceptable range when potential uncertainties, including the manufacturer’s uncertainty of the technique and standards, were taken into account. The experiments described in this article could be used as a model for validation of other instruments for similar purposes. Later studies in this series will address the more general issue of demonstrating that the IRMS technique is scientifically sound and fit‐for‐purpose in the forensic explosives analysis field.     

Age estimation from aspartic acid racemization of root dentin by internal standard method

In this study, we investigated the application of the internal standard method to determine age from aspartic acid (Asp) racemization. D-Methionine (D-Met) and D-norleucine (D-Nleu) were tested as internal standards for the purpose of validating the derivatization and gas chromatographic measurements. Using a set of standard amino acids plus the internal standards in constant volume, calibration plots with reasonable linearity (R > 0.98) were constructed. Based on the analysis of sample chromatograms, D-Met appeared to meet the criteria for internal standards, hence it was selected for use in D- and L-Asp quantification. The correlation between dentin age and D-/L-Asp ratios from the peak areas as well as from the absolute concentrations was investigated. Correlation coefficients were calculated as 0.98 and 0.90, respectively. The slight decrease in accuracy was attributed to the conversion of D-Asp/D-Met ratios to concentrations employing the calibration curves figured from pure Asp. Because the application of the internal standard method produced reproducible and precise measurements, the employment of internal standards in age estimation based on Asp racemization appears to provide quality assurance by avoiding possible errors arising from sample preparation.     

Lead Theft—A Study of the “Uniqueness” of Lead from Church Roofs

In the United Kingdom, theft of lead is common, particularly from churches and other public buildings with lead roofs. To assess the potential to distinguish lead from different sources, 41 samples of lead from 24 church roofs in Northamptonshire, U.K, have been analyzed for relative abundance of trace elements and isotopes of lead using X‐ray fluorescence (XRF) and inductively coupled plasma mass spectrometry, respectively. XRF revealed the overall presence of 12 trace elements with the four most abundant, calcium, phosphorus, silicon, and sulfur, showing a large weight percentage standard error of the mean of all samples suggesting variation in the weight percentage of these elements between different church roofs. Multiple samples from the same roofs, but different lead sheets, showed much lower weight percentage standard errors of the mean suggesting similar trace element concentrations. Lead isotope ratios were similar for all samples. Factors likely to affect the occurrence of these trace elements are discussed.     

Quantitative analysis of glasses used within Australia

An initial 134 glasses have been collected from eleven classifications of glass used within Australia. These include both local and imported glasses. Quantitative elemental analyses of the glasses have been determined using a scanning electron microscope equipped with an energy dispersive X-ray spectrometer. The current program provides for an elemental analysis for Na, Mg, Al, Si, P, S or Pb, Cl, K, Ca, Ba or Ti, V, Cr, Fe, Mn and Zn expressed as oxides, and has a sensitivity down to approximately 0.1%. The data for the six most commonly occurring elements, namely, Na, Mg, Al, Si, K and Ca, together with the refractive index are presented for each class of glass in terms of their mean value and standard deviation from the mean, and also in histogram form.     

Impurity profiling of methamphetamine hydrochloride drugs seized in the Philippines

Methamphetamine hydrochloride is one of the most widely used illicit drugs in the Philippines. In this study, we describe the application of cluster analysis of trace impurities in the profiling of the seized methamphetamine drug samples. Thirty milligrams of a homogenized drug sample were dissolved in 1 mL of pH 10.5 buffer solution and extracted with ethyl acetate containing three internal standards. The trace impurities were identified using gas chromatography-mass spectrometry (GC-MS) and quantified by gas chromatography with a flame ionization detector (GC-FID). Following previously reported methodologies, 30 impurity peaks were selected from the GC-FID chromatograms. The peak areas and retention times were referenced to the internal standards. The peak areas of the selected peaks were then grouped for cluster analysis. In order to check for consistency of clustering, two further cluster analyses were performed using 40 and 50 impurity peaks. Changes in clustering were observed in going from 30 to 40 impurity peaks, while analyses using 40 and 50 impurity peaks gave similar results. Thus, for the seized drug samples used in this study, cluster analysis using at least 40 impurity peaks showed better consistency of clustering as compared to analysis using 30 peaks only. Ten of the impurity peaks were identified, of which four were identified for the first time in methamphetamine drug samples. These are p-bromotoluene, N-benzyl amphetamine, N-ethyl amphetamine, and N-ethyl methamphetamine. The presence of phenyl-2-propanone (P2P), N,N-dimethyl amphetamine, and N-formyl amphetamine is indicative that these casework samples were synthesized using the Leuckart method.     

In- and out-flows of elements in bones embedded in reference soils

Possible exchanges of elements between bone and the surrounding soil after being embedded underground for 2 years were estimated. Bone pieces were samples from human vertebrae without any treatments after resection. Sixteen elements were determined by atomic emission mass spectrometry. These were divided into three types; Type I, an in-flow in which elements increased, as in Fe, Al and Ba; type II, a balanced decrease in which changes were found in S, Mg and Zn; and type III, an out-flow in which elements, such as Ca and P, entered into bones from embedded soils. These exchanges depended on the varying nature of soils and also on the time underground. The exchanges were progressed in duration of the time after burial. Data obtained are possible references to judge the time-lapse after burial of bones in relating to characters of soils embedded, and to identify proper bone elements from containment elements.     

Histologic detection of fat emboli

We describe a procedure for detection of fat emboli in formalin fixed tissue using osmium tetroxide postfixation. Intravascular fat in tissue postfixed in osmium tetroxide, embedded in epoxy or paraffin, and stained with toluidine blue, hematoxylin, or Oil Red O is more easily visualized than in frozen tissue that is stained with Oil Red O. With these methods, fat emboli may be detected years after the initial autopsy.     

Mitochondrial DNA error prophylaxis: assessing the causes of errors in the GEP'02-03 proficiency testing trial

A qualitative and quantitative analytical method was developed and validated for the determination of 49 licit and illicit drugs in oral fluid. Small oral fluid samples, volume 1mL, were collected from volunteers using a modified Omni-Sal device and the analytes were extracted from an oral fluid/buffer mixture using a single Bond Elut Certify solid phase extraction cartridge. Liquid chromatography-tandem mass spectrometry (LC-MS-MS) and gas chromatography-repetitive full scan mass spectrometry (GC-MS) were used in parallel to analyze the extracts for the targeted drugs. Extracts were analyzed by GC-MS in their underivatized form and as their pentafluoropropionyl derivatives. Deuterated internal standards were used for quantification of drugs of abuse by LC-MS-MS to minimize matrix effects. Methadone-d(9) and tumoxetine were used as the internal standards for quantification of non-derivatized and derivatized analytes respectively by GC-MS. Linearity was demonstrated over the range 5-200 ng/mL and limits of detection were less than 4 ng/mL for each drug analyzed. The method demonstrated acceptable recoveries for most of the analytes and good intra- and inter-day precision. Acquisition of data by repetitive full scan GC-MS allows the addition of further analytes to the target menu.