Visualization of gunshot residue patterns on dark clothing

ABSTRACT: Determination of the muzzle‐to‐target distance is often a critical factor in criminal and civil investigations involving firearms. However, seeing and recording gunshot residue patterns can be difficult if the victim's clothing is dark and/or bloodstained. Trostle reported the use of infrared film for the detection of burn patterns. However, only after the film is developed are the results visible and multiple exposures at different settings may be needed. The Video Spectral Comparator^? 2000 (Foster & Freeman Ltd., Evesham, Worcestershire, U.K.) is an imaging instrument routinely used by forensic document examiners. Without use of specialized film could the VSC 2000 (at appropriate instrument settings) quickly, easily, and reliably provide instantaneous viewing, saving, and printing of gunshot residue patterns on dark and/or blood soaked clothing? At muzzle‐to‐target distances of 6, 12, and 18 in., test fires were made into five different types of dark clothing using eight different handguns of different calibers. Gunshot residues were detected for all eight calibers, and powder burn patterns were seen on dark clothing for all three target distances and calibers except 0.22 long rifle and 0.25 ACP. Bloodstains did not preclude the viewing of these patterns.     

Inherent Fluorescence Detection of Latent Fingermarks by Homemade Shortwave Ultraviolet Laser

Detection of latent fingermarks on various substrates is critical in crime investigations. Conventional chemical methods using reagents could contaminate or even destruct biological information of samples. Here, an optical method and successful case application of detecting latent fingermarks through long‐wave ultraviolet (UV) fluorescence (300–400 nm) by shortwave UV laser excitation is reported. Experimental results indicate that the recovery rate of the latent fingermarks on various paper items is in the range of 70–80% without chemical treatments. Moreover, the optical method allows for the preservation of samples for further examination, such as polymerase chain reaction (PCR) testing. The technique has also been successfully applied to a criminal case in identifying the suspect, which, to the best of our knowledge, has never been reported in real crime investigations. Therefore, such a method as UV‐excited UV fluorescence in detecting latent fingermarks may be better for examination in cases where biological information of samples is needed for consequent testing.     

VSC文检仪在文件鉴定中的应用研究

VSC文件检验仪具有不破坏被检验材料、高效、直观等优点,是目前文件技术检验中普遍使用的检验方法。本文利用该仪器较系统地对文件鉴定中常见的书写材料的光学特性,及其在文件鉴定实践中的应用作了较全面的研究,并对如何获得最佳检验结果和对检验结果如何作出科学的评价等方面进行了探讨,希望能为文件鉴定的实践及制定有关的技术检验规范时提供参考。     

Prepared Disappearing Ink and Deciphering of Documents

Disappearing inks can be used for forgeries in many fields. In this study, thymolphthalein indicator solution was prepared as a disappearing ink. A total of 54 different solutions containing thymolphthalein were prepared at six different concentrations and nine different pH values. Among the prepared solutions, 0.16 g/50 mL and 0.32 g/65 mL thymolphthalein at pH 14 were the optimum solutions that were not distinguishable from regular ink when applied to promissory note. Fountain pens were filled with the abovementioned ink solutions and applied to promissory notes for experimental purposes. After 40 h, ink residues were not visible on promissory notes written with the ink with the optimum pH (pH = 14) value. To decipher the entries that disappeared, an instrumental method (Video Spectral Comparator‐8000) and a chemical method (using NH₃ vapor) were used, succeeded at 0.32 g/65 mL, but failed at 0.16 g/50 mL thymolphthalein. Therefore, NH₃ had to be sprayed for 0.16 g/50 mL with negligible harm.     

How Much Can a Forensic Laboratory Do to Discriminate Questioned Ink Entries?

Questioned document examiners are frequently required to determine whether the questioned ink entries on a document are written with the same ink, either for forged document identification or relative ink dating. How many methods are sufficient to discriminate potentially different inks? In this paper, 18 blue ballpoint inks were first nondestructively examined with a video spectral comparator. The ink entries were subsequently extracted with organic solvents for analysis of the volatile solvents and dyes by GC/MS, TLC, and LC‐MS/MS. The 18 ink samples were divided into 10, 9, 12, and 14 categories by these four methods, respectively. With the combined results, there were only two inks that remained indistinguishable, but they were further differentiated by microscopy. Therefore, to achieve effective discrimination of ballpoint ink entries, the authors suggest that a complete examination should include an analysis of their optical features, volatile solvents, and dyes as well as the ink quality.     

Evaluation of two instrumental methods of comparing writing paper

An organization had approved the sample of writing paper, and accordingly the supplier had to execute the supply. The supply received was suspected to be of different quality from approved one. The organization sent the samples for comparison to the Forensic Science Laboratory. Both the approved and supplied samples were compared using Tensile Testing Method with the Material Testing Machine and Fluorescence and spectral analysis using the Video Spectral Comparator (VSC2000). The difference between the mean loads at peak before rupture in the tensile testing mode for the two samples was about 33%. The two samples differed significantly in terms of UV fluorescence, and there was about 5% average difference in the percentage of maximum reflected intensity in the wavelength region of 400-900 nm. It has been observed in this study that these two methods can adequately distinguish paper samples of different origin.     

Tattoos and Human Identification: Investigation into the Use of X‐Ray and Infrared Radiation in the Visualization of Tattoos

Any person with a tattoo known to their family or friends could potentially be identified from the presence of such personal identifying markers. Problems in identification utilizing tattoos may arise when these markers are removed or defaced in some way. This paper uses infrared wavelengths at 760, 850, and 950 nm to improve the visualization of laser‐removed or covered up tattoos and also to establish whether the ink pigments used can be observed on radiographs from any metal that may be present. The results obtained indicate that some older inks have a high enough metallic content to allow them to be viewed on a radiograph, while infrared light can demonstrate latent ink still present in the skin after laser removal and can also be utilized to distinguish an original tattoo through a secondary “cover‐up” tattoo. Infrared photography and radiography have been shown to improve tattoo visualization in a forensic context.     

Development of microwave-assisted extraction procedure for organic impurity profiling of seized 3,4-methylenedioxymethamphetamine (MDMA)

Abstract: Organic impurity profiling of seized 3,4‐methylenedioxymethamphetamine (MDMA) tablets aims to link tablets to common production sources. Conventionally, organic impurities are extracted from tablets using a liquid–liquid extraction (LLE) procedure prior to analysis by gas chromatography–mass spectrometry (GC‐MS). In this research, the development of an alternative microwave‐assisted extraction/headspace solid‐phase microextraction (MAE/HS‐SPME) procedure is described. The optimal procedure used phosphate buffer (1 M, pH 8), with an HS‐SPME extraction temperature of 70°C for 40 min, using a divinylbenzene/Carboxen?/polydimethylsiloxane (DVB/CAR/PDMS) fiber. Impurities were extracted from seized MDMA exhibits using the MAE/HS‐SPME procedure, as well as HS‐SPME alone, and a conventional LLE procedure. The HS‐SPME procedure was deemed to be the most practical because of the affordability and need for less analyst involvement. Although the LLE was limited in the number of impurities extracted, the procedure is still useful for the extraction of less volatile impurities that are not extracted by HS‐SPME.     

The Effects of High Dynamic Range on Fingerprint Images Processed by Photoshop

High dynamic range (HDR) imaging is a function that combines five images with different exposures into a single image. This technique may provide fine ridge details of fingerprint images for forensic latent fingerprint examination. Therefore, viewing fingerprints under optimal conditions is of paramount importance. This paper analyzes HDR and non‐HDR photos by using the Michelson contrast formula. The Michelson formula will provide a measurement to determine whether better contrast between the background and print can be achieved using the HDR function and if the background color affects the quality of the images. Two hypothesis were tested: (i) the HDR image provides more details of fingerprints with a better tone, greater clarity, and contrast than a normally exposed image regardless of the background color; (ii) the background color does not affect the quality of HDR fingerprint images overall, but the multi‐color background may increase the contrast of HDR fingerprint images in some cases.     

Development of Latent Fingermarks on Various Surfaces Using ZnO‐SiO2 Nanopowder

Fingermarks are one of the most useful forms of evidence in identification and can provide generalized proof of identity in crime investigation. They are developed using various conventional powders. The novel nanopowder ZnO‐SiO₂ was synthesized via the conventional heating method and characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), energy‐dispersive X‐ray (EDX) analysis, transmission electron microscope (TEM), and X‐ray diffraction (XRD). The mean particle size of ZnO‐SiO₂ nanopowder calculated through TEM was 32.9 nm. The development of fingermarks was carried out by powder dusting and small particle reagent (SPR) methods. Powder dusting method was used for the development of latent fingermarks on various dry, nonporous, and semi‐porous surfaces. The SPR method was also applied to wet nonporous surface. The developed latent fingermarks using ZnO‐SiO₂ nanopowder were found to have excellent quality with very clear third‐level ridges detail and had better visibility than commercially available white powder.     

Visualization of Fingermarks Deposits on Untreated Thermal Paper Exploiting the Near Infrared Luminescence

Thermal paper is widely used as a print medium for different applications but it constitutes a tricky substrate for fingermark visualization. An earlier work (J Forensic Sci 2015; 60 :1034) reported how to visualize fingermarks on untreated thermal paper by illuminating the item with a UV-A light source. In the present paper, the potential of the near infrared (NIR) luminescence has been tested on thermal paper compared to the mentioned method. A controlled study was carried out utilizing eccrine enriched fingermarks. The promising outcomes obtained were further confirmed by performing a pseudo-operational trial. Data clearly showed that the use of the NIR filter gave better results. Finally, preliminary tests suggested a different mechanism of reaction induced by fingermarks with respect to the one behind the thermal printing. Thus, NIR luminescence represents a refinement to the suite of optical examination processes, including the potential to increase the number of marks recovered in a noncontact, nondestructive way.     

Taphonomic Effects of Mechanical Plowing on Buried Juvenile‐Sized Remains

Agricultural activity is a worldwide taphonomic process and can present unique challenges in the recovery of buried remains. Previous research has been mostly within the realm of site formation processes of archeological sites utilizing only surface material. This research expands upon the previous research by incorporating the distribution of subsurface material by the use of archeological excavation techniques. An experiment was conducted utilizing juvenile pig (Sus scrofa) skeletons buried in relative anatomical position at two different depths (15 cm below the surface [cmbs] and 22 cmbs). The burials were then subjected to different intervals of mechanical plowing: one, three, five, seven, or 10 plow passes. The skeletal material was recovered using pedestrian survey followed by hand excavation and screening of all sediments. This research shows that there is a significant relationship between the degree of plowing and the distance skeletal material is distributed and the percentage of material recovered undamaged.     

5种免提取试剂盒检验滤纸血痕结果的比较

目的探讨5种免提取试剂盒对滤纸血痕样本检验的效果。方法陈旧滤纸血痕(存放时间12～14个月)及新鲜滤纸血痕(存放时间小于1个月)各920份,分别随机分为5组。应用AGCU 17+1、Goldeneye 20A、Powerplex16HS、Identifiler Plus、Identifiler Direct 5种免提取试剂盒进行检验,对比各组检验结果。结果陈旧滤纸血痕5种试剂盒的检验成功率为98.91%～100%,各组间无差异(P>0.05);新鲜滤纸血痕,Identifiler Plus和Identifiler Direct试剂盒检验成功率高于AGCU17+1、Goldeneye 20A及Powerplex 16HS试剂盒(P<0.01);将样本做陈旧化处理后再用成功率较低的3种试剂盒进行检验,成功率分别升至100%、99.46%、99.46%;Identifiler Plus试剂盒扩增循环27次效果优于28次。结论本文5种试剂盒均可用于滤纸血痕的直接扩增检验,但使用AGCU17+1、Goldeneye 20A及Powerplex 16HS试剂盒需将新鲜血痕做陈旧化处理;Identifiler Plus试剂盒需将循环次数降为27次。     

Novel O‐propyl,S‐propyl,and N‐propyl substituted 1,4‐naphthoquinones and 1,4‐anthraquinones as potential fingermark development reagents for porous surfaces

Lawsone is a 2‐substituted‐1,4‐naphthoquinone derivative, which has been proposed as an alternative to the reagents currently used for fingermark detection on porous surfaces. 2‐substituted‐anthraquinones, which contain an additional conjugated benzene ring, have a similar chemical structure to that of lawsone. In this study, a new series of 2‐substituted‐1,4‐naphthoquinones and 2‐substituted‐1,4‐anthraquinones were synthesized and completely characterized by¹H NMR,¹³C NMR, IR, and HPLC‐TOF/MS analyses. All newly synthesized 2‐substituted‐1,4‐quinones were investigated for their ability to develop latent fingermarks on porous surfaces, and this ability was compared with that of lawsone. Each fingermark developed was graded using an established method; thus, quantitative data were attributed to each fingermark. It has been demonstrated that the 1,4 ‐ quinones react with amino acids present in latent fingermarks on selected paper surfaces to produce faint yellow‐orange impressions, which exhibit strong photoluminescence when illuminated with a forensic light source at 440 nm and observed through a red filter. None of the compounds caused background darkening. The results obtained were generally similar to those of lawsone, however, 8‐dibromo‐2‐(propylamino)naphthalene‐1,4‐dione and 5,8‐dibromo‐2‐(propylthio)naphthalene‐1,4‐dione yielded better results for copier paper and colored (blue) copier paper used in this analysis. To the best of our knowledge, this is the first study to examine the role of 1,4‐anthraquinone derivatives as potential fingermark development reagents. The results indicate that 1,4‐quinones have a potential to be used as reagents for enhancement of latent fingermarks.     

Comparative Evaluation of Potentially Radiolucent Projectile Components by Radiographs and Computed Tomography

Projectile components that are traditionally radiolucent can be of considerable importance in determination of weapon type and caliber, but they are often missed on evaluation of postmortem radiographs. We hypothesized that these components would be significantly better visualized by evaluation of computed tomography (CT) scans compared to the practice standard of radiography alone. In this project, potentially radiolucent projectile components were both pulled apart and fired, and the radiolucent components were recovered. These components were embedded in blocks of ballistics gelatin and were imaged using both radiography and CT. The scans were evaluated by three blinded, board‐certified radiologists for the presence/absence of projectile components and true‐negative regions in each block. If a radiologist indicated visualization of a projectile component, they were further requested to describe their observation. It was found that traditionally radiolucent projectile components are not significantly more often identified on CT scans than radiography (p < 0.05).     

A New Method for the Removal and Analysis of Small Particles Adhering to Carpet Fiber Surfaces,,

Fibers are a commonly encountered evidence type and fiber comparisons are routinely conducted. When the characteristics of questioned and known fibers correspond, the probative value is limited because the characteristics compared are determined by their manufacture. It would be valuable to test the hypothesis that questioned fibers originated from a specific carpet. One means of testing this is to analyze fine particles on the fibers. A procedure was developed for removing adhering particles from fibers and preparing them for scanning electron microscopy/ energy dispersive X‐ray spectrometry (SEM/EDS) analysis. The efficacy of several fluids (acetone, ethanol, hexanes, aqueous ethanol, aqueous sodium hexametaphosphate) and agitation methods (sonication and vortexing) for removing particles from fibers was evaluated. The most effective method evaluated was sonication in ethanol for 10 min. The recovered particles were filtered onto a polycarbonate filter and analyzed by automated SEM/EDS analysis to generate data on the particle assemblage. This method makes possible future research to test the within‐item and between‐item variability of particle assemblages on fibers.     

Contactless Visualization of Latent Fingerprints on Nonporous Curved Surfaces of Circular Cross Section—A Statistical Evaluation on the Materials as Plane Mirror

A new contactless technique for latent fingerprint visualization on nonporous curved surfaces of circular cross section was introduced by Low et al. (1). The technique utilizes a plane mirror to convey the light rays toward the inspected surfaces for latent fingerprint visualization. This research activity came up as an extension of the previous study which utilized an aluminum plate as the plane mirror to illuminate the inspected surfaces. Dulling spray was used to increase the diffuse component of the reflective aluminum plate. However, the amount of dulling spray will affect the uniformity of the illumination on the inspected curved surfaces. In this study, a study on the new materials for the plane mirror was carried out. Coated aluminum, opal, and ground glass diffusers were selected as the new materials. The performance of the new materials was compared to the aluminum based on the quality of the captured images on various nonporous cylindrical surfaces. A statistical approach known as randomized complete block design was used to design the experiment. The quality of the captured images was obtained using Spectral Image Validation and Verification. Two‐way analysis of variance and Fisher's least significant difference test were used to analyze the quality of the images. From the results of the statistical analysis, coated aluminum has the best performance compared to aluminum, opal, and ground glass diffusers.     

The Use of Near‐Infrared Photography to Image Fired Bullets and Cartridge Cases

An imaging technique that is capable of reducing glare, reflection, and shadows can greatly assist the process of toolmarks comparison. In this work, a camera with near‐infrared (near‐IR) photographic capabilities was fitted with an IR filter, mounted to a stereomicroscope, and used to capture images of toolmarks on fired bullets and cartridge cases. Fluorescent, white light‐emitting diode (LED), and halogen light sources were compared for use with the camera. Test‐fired bullets and cartridge cases from different makes and models of firearms were photographed under either near‐IR or visible light. With visual comparisons, near‐IR images and visible light images were comparable. The use of near‐IR photography did not reveal more details and could not effectively eliminate reflections and glare associated with visible light photography. Near‐IR photography showed little advantages in manual examination of fired evidence when it was compared with visible light (regular) photography.     

A New Approach for the Carbon Monoxide (CO) Exposure Diagnosis: Measurement of Total CO in Human Blood Versus Carboxyhemoglobin (HbCO)

The aim of the study is to present the application of a headspace–gas chromatography–mass spectrometry (HS‐GC‐MS) method for the determination of the carbon monoxide (CO) blood concentration and to compare it with carboxyhemoglobin (HbCO) saturation. In postmortem cases, the HbCO measured by spectrophotometry frequently leads to inaccurate results due to inadequate samples or analyses. The true role of CO intoxication in the death of a person could be misclassified. The estimation of HbCO from HS‐GC‐MS CO measurements provides helpful information by determining the total CO levels (CO linked to hemoglobin (HbCO) and CO dissociated from hemoglobin). The CO concentrations were converted in HbCO saturation levels to define cutoff blood CO values. CO limits were defined as less than 1 μmol/mL for living persons, less than 1.5 μmol/mL for dead persons without CO exposure, and greater than 3 μmol/mL for dead persons with clear CO poisoning.     

Contributions from Forensic Imaging to the Investigation of Upper Cervical Fractures

Abstract: Injuries to the upper cervical spine (UCS) are common in traumatic deaths and postmortem computed tomography (PMCT) may contribute to the forensic investigation. This study presents PMCT in comparison with autopsy in the examination of UCS injury. Thirteen consecutive cases with UCS fracture and/or cranio‐cervical dislocation were examined with PMCT and autopsy, and the findings were correlated. Neither of the techniques identified all UCS injuries. Fractures of atlas and axis were best visualized with PMCT whereas cranio‐cervical dislocation was better identified during autopsy. Serious injuries were present after both high‐ and low‐energy trauma. Medico‐legal autopsy in combination with PMCT produced a thorough evaluation of UCS injuries. By combining these procedures detailed investigations, including accident reconstruction and injury pattern analysis, can be performed. This study supports the routine application of PMCT, as a supplement to the medico‐legal autopsy of deaths with UCS injuries.