Nanomanipulation‐Coupled Nanospray Mass Spectrometry Applied to the Extraction and Analysis of Trace Analytes Found on Fibers*

Abstract: This article presents the novel instrumentation of nanomanipulation coupled to nanospray ionization‐mass spectrometry, which is used to directly probe trace analytes found on individual fibers. The low detection limits and sample volumes associated with nanospray ionization‐mass spectrometry make it the ideal instrument to implement for trace analysis. Nanospray ionization‐mass spectrometry, coupled with the nanomanipulator, allows for the direct probing of trace particulates on fibers. The technique is demonstrated by dissolving an electrostatic particle of cocaine from a fiber, collecting the analyte solution in a nanospray tip, and transferring the tip directly to the mass spectrometer to complete analysis. The utility of this technique is evident through the minimal sample preparation and short analysis time. The use of nanomanipulation coupled to nanospray ionization‐mass spectrometry could improve on current trace particulate analysis by reducing both detection limits and sample size required to complete analysis.     

Carbon‐Based Fingerprint Powder as a One‐Step Development and Matrix Application for High‐Resolution Mass Spectrometry Imaging of Latent Fingerprints

Carbon‐based materials are often used as matrices for matrix‐assisted laser desorption/ionization mass spectrometry (MALDI‐MS) and its imaging (MALDI‐MSI). However, researchers have refrained from using carbon‐based fingerprint powder (CFP) as a matrix due to high background and contamination. In this work, the compatibility of CFP is reevaluated with MALDI‐MSI using a high‐resolution mass spectrometer (HRMS) and compared to traditional organic matrices. Relevant fingerprint compounds were easily distinguished from carbon cluster peaks when using HRMS. For fair comparison, half of a fingerprint was dusted with CFP while the other half was dusted with traditional organic matrices. All compounds studied had comparable, or higher, signal‐to‐noise (S/N) ratios when CFP was used as the matrix. Additionally, chemical image qualities closely followed the trend of S/N ratios. CFP proved to be an effective one‐step development and matrix application technique for MALDI‐MSI of latent fingerprints, when carbon cluster peaks are well separated by a HRMS.     

Effect of Aging and Surface Interactions on the Diffusion of Endogenous Compounds in Latent Fingerprints Studied by Mass Spectrometry Imaging,

The ability to determine the age of fingerprints would be immeasurably beneficial in criminal investigations. We explore the possibility of determining the age of fingerprints by analyzing various compounds as they diffuse from the ridges to the valleys of fingerprints using matrix‐assisted laser desorption/ionization mass spectrometry imaging. The diffusion of two classes of endogenous fingerprint compounds, fatty acids and triacylglycerols (TGs), was studied in fresh and aged fingerprints on four surfaces. We expected higher molecular weight TGs would diffuse slower than fatty acids and allow us to determine the age of older fingerprints. However, we found interactions between endogenous compounds and the surface have a much stronger impact on diffusion than molecular weight. For example, diffusion of TGs is faster on hydrophilic plain glass or partially hydrophilic stainless steel surfaces, than on a hydrophobic Rain‐x treated surface. This result further complicates utilizing a diffusion model to age fingerprints.     

Photo‐ and Thermal‐Degradation Studies of Select Eccrine Fingerprint Constituents

Abstract: Photo‐ and thermal‐degradation studies on eccrine fingerprint components are presented herein. Dilute distinct solutions of urea, lactic acid, and seven amino acids were deposited on steel coupons and Teflon^® disks, exposed to artificial sunlight or heat, extracted, and analyzed. This aim of this study was to determine whether the investigated eccrine components, previously determined to be Raman active for a parallel study, experienced photo‐ or thermally induced degradation, and if so, to determine the rate and identify any detectable products. Neither the amino acids nor urea exhibited photo‐degradation; however, when heated for a period of three minutes, the onset of thermal‐degradation was initiated at 100°C for the amino acids and 100°C for urea. Lactic acid, the major polymerization initiator of superglue fuming, showed photochemical and thermal‐degradation. These results could be used for future development of new latent fingerprint visualization methods, especially when lactic acid is degraded.     

Evaluation of Four Fingerprint Development Methods for Touch Chemistry Using Matrix‐Assisted Laser Desorption Ionization/Time‐of‐Flight Mass Spectrometry,

Four preparation techniques for MALDI/TOF mass spectrometry were compared to determine the ability to gather intelligence for investigations through the chemical analysis of latent fingerprints, defined as “touch chemistry.” Compatible fingerprint development processes used for identification along with new techniques are necessary to evaluate touch chemistry. Ten volunteers deposited fingerprints from solvent residues containing drugs and explosives onto microscope slides. The developers included (A) fingerprint powder, (B) MALDI matrix, (C) fingerprint powder and lifting, and (D) cyanoacrylate fuming with fingerprint powder. Qualitative identification was based on ion images and spectra. The highest average detection rates (88%) were found using methods A and B. Methods C (52%) or D (18%) had limited success. Results demonstrate the importance of imaging coupled to extracted mass spectral data in detecting analytes in deposited fingerprints. Overall, the results suggest continued development of touch chemistry applications could prove useful for gathering intelligence and forensically relevant information.     

Quantitative Analysis of Gamma‐Hydroxybutyrate at Endogenous Concentrations in Hair using Liquid Chromatography Tandem Mass Spectrometry

Abstract: A method capable of quantifying endogenous concentrations of gamma‐hydroxybutyrate (GHB) in human head hair was developed and validated using liquid chromatography/mass spectrometry/mass spectrometry (LC/MS/MS). Hair was digested under alkaline conditions, and GHB was isolated using liquid–liquid extraction. LC/MS/MS was performed using atmospheric pressure chemical ionization in the negative mode, multiple reaction monitoring, and deuterated internal standard (GHB‐D₆). Linearity was observed between 0.1 and 100 ng/mg GHB (R² = 1.000). The limits of detection and quantitation in human hair were 0.2 and 0.4 ng/mg, respectively. Accuracy at 2 ng/mg and 10 ng/mg was determined to be 97% and 94%, and intra‐assay CVs at these concentrations were 5.2% and 7.4% (n = 4). Beta‐hydroxybutyrate (BHB), alpha‐hydroxybutyrate, gamma‐butyrolactone, and 1,4‐butanediol did not produce an interference, and there was negligible ion suppression or enhancement from the matrix.     

Forensic Analysis of Stains on Fabric Using Direct Analysis in Real‐time Ionization with High‐Resolution Accurate Mass‐Mass Spectrometry

A rapid technique using direct analysis in real ‐ time (DART) ambient ionization coupled to a high ‐ resolution accurate mass‐mass spectrometer (HRAM‐MS) was employed to analyze stains on an individual's pants suspected to have been involved in a violent crime. The victim was consuming chocolate ice cream at the time of the attack, and investigators recovered the suspect's pants exhibiting splatter stains. Liquid chromatography with mass spectral detection (LC‐MS) and stereoscopic light microscopy (SLM) were also utilized in this analysis. It was determined that the stains on the pants contained theobromine and caffeine, known components of chocolate. A shard from the ceramic bowl that contained the victim's ice cream and a control chocolate ice cream sample were also found to contain caffeine and theobromine. The use of DART‐HRAM‐MS was useful in this case due to its rapid analysis capability and because of the limited amount of sample present as a stain.     

Characterization and Differentiation of Geometric Isomers of 3‐methylfentanyl Analogs by Gas Chromatography/Mass Spectrometry,Liquid Chromatography/Mass Spectrometry,and Nuclear Magnetic Resonance Spectroscopy

The cis and trans isomers of 3‐methylfentanyl and its three analogs were chemically synthesized, and these compounds were characterized and differentiated by gas chromatography/mass spectrometry (GC/MS), liquid chromatography/mass spectrometry (LC/MS), and nuclear magnetic resonance (NMR) spectroscopy. The cis and trans isomers of the 3‐methylfentanyl analogs were completely separated by GC/MS. Although the high temperature of the GC injection port caused thermal degradation of β‐hydroxy‐3‐methylfentanyl, the degradation was completely suppressed by trimethylsilyl derivatization. The isomers were also well separated by LC/MS on an octadecylsilyl column with 10 mM ammonium acetate and methanol as the mobile phase. The proton NMR signals were split when the hydrochloride salts of the 3‐methylfentanyl analogs were dissolved in deuterated chloroform because stereoisomers were formed by the coordination of the hydrochloride proton to the nitrogen of the piperidine ring of the 3‐methylfentanyl analogs.     

Detection of Gunshot Residue in Blowfly Larvae and Decomposing Porcine Tissue Using Inductively Coupled Plasma Mass Spectrometry (ICP‐MS)*

Abstract: Blowfly larvae and porcine tissue contaminated with gunshot residue (GSR) were collected during summer and winter months, over a 37‐day and a 60‐day sampling period, respectively. Wound samples were microwave‐digested and analyzed by inductively coupled plasma mass spectrometry (ICP‐MS) for the detection of antimony, barium, and lead. During summer, the 37‐day sampling period encompassed all stages of decomposition, except skeletonization. The three elements were detected in larvae only on days 3 and 4 after death but were detected at significant levels in tissue samples throughout the entire sampling period. In winter, no significant decomposition was observed throughout the 60‐day sampling. Although temperatures were too low for blowfly activity, the three elements were detected in the tissue samples at relatively constant, significant levels. Hence, GSR determination in tissue was more dependent on decomposition stage rather than time since death.     

Anion Identification via Complexation with meso‐octamethylcalix(4)pyrrole and Detection Using Electrospray Ionization Mass Spectrometry*

Abstract: The routine identification of controlled substances and adulterants during forensic chemistry analysis often involves the identification of counter ions or salt forms present in an exhibit. Here, the use of the compound meso‐octamethylcalix(4)pyrrole (C4P) during salt‐form identification analysis is presented. C4P is a commercially‐available, anion‐binding agent that can be reacted with a controlled substance or adulterant, resulting in the sequestration of anionic species, usually present as counter ions to the active ingredient. Formation of noncovalent complexes between the cyclic host C4P compound and anionic guests is investigated using electrospray ionization–mass spectrometry (ESI–MS). Complexes with chloride, bromide, iodide, nitrate, and acetate are readily observed and mass spectrometry analysis provides identification via molecular weight characterization. Chloride and bromide complexes are also characterized by the isotopic distribution of their molecular ions. Formation of host–guest complexes is not observed for sulfate and phosphate salts, presumably due to steric hindrance and energetically unfavorable conditions.     

Determination of Trace Elemental Concentrations in Document Papers for Forensic Comparison Using Inductively Coupled Plasma–Mass Spectrometry

Abstract:  With improvements in manufacturing procedures, comparing physical characteristics of paper samples may not offer sufficient discrimination among different vendors. In this work, the potential to differentiate paper samples based on trace element concentrations was investigated. Paper samples from two different vendors were microwave-digested and trace element concentrations (Mg, Al, Mn, Fe, Sr, Y, Ba, Ce, and Nd) were determined using inductively coupled plasma–mass spectrometry. Differences in concentration were assessed statistically using two-way ANOVA and Tukey's honestly significant differences test. Elemental concentrations were shown to be consistent across a single sheet as well as within a single ream of paper for each vendor. Reams from vendor A were differentiated based on Al and Ba concentration while reams from vendor B were differentiated based on Mg, Mn, and Sr concentrations. Paper was differentiated according to vendor based on significant differences in Ba, Sr, Ce, and Nd concentrations.     

Detection and Classification of Ignitable Liquid Residues in the Presence of Matrix Interferences by Using Direct Analysis in Real Time Mass Spectrometry,

Conventional Gas Chromatography‐Mass Spectrometry (GC‐MS) methods for the analysis of ignitable liquids (ILs) are usually time‐consuming, and the data produced are difficult to interpret. A fast IL screening method using direct analysis in real time mass spectrometry (DART‐MS) is proposed in this study. GC‐MS, QuickStrip DART‐MS, and thermal desorption DART‐MS methods were used to analyze neat ILs and thermal desorption DART‐MS without extraction was used to analyze ILs on five substrates (e.g., carpet, wood, cloth, sand, and paper). Compared to GC‐MS, DART‐MS methods generated different spectral profiles for neat ILs with more peaks in the higher mass range and also provided better detection of less volatile compounds. ILs on substrates were successfully classified (98 ± 1%) using partial least squares discriminant analysis (PLS‐DA) models based on thermal desorption DART‐MS data. This study shows that DART‐MS has great potential for the high‐throughput screening of ILs on substrates.     

Evaluation of the Forensic Utility of Scanning Electron Microscopy‐Energy Dispersive Spectroscopy and Laser Ablation‐Inductively Coupled Plasma‐Mass Spectrometry for Printing Ink Examinations

Improvements in printing technology have exacerbated the problem of document counterfeiting, prompting the need for analytical techniques that better characterize inks for forensic analysis and comparisons. In this study, 319 printing inks (toner, inkjet, offset, and Intaglio) were analyzed directly on the paper substrate using scanning electron microscopy‐energy dispersive spectroscopy (SEM‐EDS) and Laser Ablation‐Inductively Coupled Plasma‐Mass Spectrometry (LA‐ICP‐MS). As anticipated, the high sensitivity of LA‐ICP‐MS pairwise comparisons resulted in excellent discrimination (average of ~ 99.6%) between different ink samples from each of the four ink types and almost 100% correct associations between ink samples known to originate from the same source. SEM‐EDS analysis also resulted in very good discrimination for different toner and intaglio inks (>97%) and 100% correct association for samples from the same source. SEM‐EDS provided complementary information to LA‐ICP‐MS for certain ink types but showed limited utility for the discrimination of inkjet and offset inks.     

Detection of Brodifacoum and other Rodenticides in Drug Mixtures using Thermal Desorption Direct Analysis in Real Time Mass Spectrometry (TD‐DART‐MS)

In recent months, there has been increased reporting of seized drug and toxicology cases containing rodenticides, the active ingredient in rat poisons. Seeing as rodenticides are not scheduled substances, they are not commonly screened for in seized drug analysis. This work investigates the use of TD‐DART‐MS for the simultaneous detection of rodenticides and drugs. Six rodenticides were evaluated, an optimal method was established, and limits of detection in the tens of nanograms were calculated. Additional studies highlight that detection at less than 1% by weight in mixtures with AB‐FUBINACA, cocaine, heroin, or methamphetamine was possible. This work presents an optimized method for detection of these compounds, allowing for the simultaneous detection of drugs and rodenticides, providing drug chemists with a tool for rapid identification of these compounds for forensic or public health purposes.     

Infrared Spectra of U.S. Automobile Original Finishes (Post – 1989). VIII: In Situ Identification of Bismuth Vanadate Using Extended Range FT‐IR Spectroscopy,Raman Spectroscopy,and X‐Ray Fluorescence Spectrometry

Chrome Yellow (PbCrO₄·xPbSO₄) was a common pigment in U.S. automobile OEM finishes for more than three decades, but in the early 1990s its use was discontinued. One of its main replacements was Bismuth Vanadate (BiVO₄·nBi₂MoO₆, n = 0–2), which was commercially introduced in 1985, as this inorganic pigment also produces a very bright hue and has excellent outdoor durability. This paper describes the in situ identification of Bismuth Vanadate in automotive finishes using FT‐IR and dispersive Raman spectroscopy and XRF spectrometry. Some differentiation of commercial formulations of this pigment is possible based on far‐infrared absorptions, Raman data, and elemental analysis. The spectral differences arise from the presence or absence of molybdenum, the use of two crystal polymorphs of BiVO₄, and differences in pigment stabilizers. Bismuth Vanadate is usually not used alone, and it is typically found with Isoindoline Yellow, hydrous ferric oxide, rutile, Isoindolinone Yellow 3R, or various combinations of these.     

The Potential of Isotope Ratio Mass Spectrometry (IRMS) and Gas Chromatography‐IRMS Analysis of Triacetone Triperoxide in Forensic Explosives Investigations

Studying links between triacetone triperoxide (TATP) samples from crime scenes and suspects can assist in criminal investigations. Isotope ratio mass spectrometry (IRMS) and gas chromatography (GC)‐IRMS were used to measure the isotopic compositions of TATP and its precursors acetone and hydrogen peroxide. In total, 31 TATP samples were synthesized with different raw material combinations and reaction conditions. For carbon, a good differentiation and a linear relationship were observed for acetone–TATP combinations. The extent of negative (δ¹³C) fractionation depended on the reaction yield. Limited enrichment was observed for the hydrogen isotope (δ²H) values of the TATP samples probably due to a constant exchange of hydrogen atoms in aqueous solution. For oxygen (δ¹⁸O), the small isotopic range and excess of water in hydrogen peroxide resulted in poor differentiation. GC‐IRMS and IRMS data were comparable except for one TATP sample prepared with high acid concentration demonstrating the potential of compound‐specific isotope analysis. Carbon IRMS has practical use in forensic TATP investigations.     

Differentiation of Twenty‐One Glitter Lip‐Glosses by Pyrolysis Gas Chromatography/Mass Spectroscopy*

Abstract: Differentiation of 21 glitter lip‐glosses from seven manufacturers was attempted by pyrolysis gas chromatography/mass spectroscopy. Samples were pyrolyzed on a ribbon probe at 800°C for 20 sec and analyzed with an Agilent^® 6890N Network GC System and Agilent^® 5973 Network Mass Selective Detector with MSD Productivity ChemStation^® Data Analysis software. The total ion chromatograms obtained were examined and differences in the presence or absence of certain chromatographic peaks corresponding to certain pyrolysis products (e.g., styrene, cyclohexane) noted. In cases where the total ion chromatograms between lip‐glosses were similar, select ion profiling was performed. Of the 21 lip‐glosses, 15 were differentiated by either the total ion chromatograms alone or through select ion profiling. Considering that lip‐glosses are typically worn by young women (who are disproportionately victims of sexual assault), this study offers the potential of being able to provide investigative leads in sexual assault investigations with evidentiary samples of this kind.     

Postmortem Blood Concentrations of R‐ and S‐Enantiomers of Methadone and EDDP in Drug Users: Influence of Co‐Medication and P‐glycoprotein Genotype

Abstract: We investigated toxicological and pharmacogenetic factors that could influence methadone toxicity using postmortem samples. R‐ and S‐methadone were measured in femoral blood from 90 postmortem cases, mainly drug users. The R‐enantiomer concentrations significantly exceeded that of the S‐enantiomers (Wilcoxon’s test, p < 0.001). The samples were divided into four groups according to other drugs detected (methadone only, methadone and strong analgesics, methadone and benzodiazepines, or methadone and other drugs). There was no significant difference in any of the R‐methadone/total methadone ratios among the four groups. The median R/S ratio was 1.38, which tends to be higher than that reported for the plasma of living subjects. In addition, we investigated whether small nucleotide polymorphisms in the MDR1 gene that encode the drug transporter P‐glycoprotein were associated with the concentrations of R‐ and S‐methadone and its metabolite 2‐ethylidene‐1,5‐dimethyl‐3,3‐diphenylpyrrolidine. No significant association was detected.     

Simultaneous Determination of 13 Anticoagulant Rodenticidesin Human Blood by Liquid Chromatography–Tandem Mass Spectrometry and its Application in Three Poisoning Cases

Anticoagulant rodenticides are widely used for rodent control around the world. A rapid and sensitive method was developed and validated for the simultaneous determination of 13 anticoagulant rodenticides (coumafuryl, pindone, valone, warfarin, coumatetralyl, coumachlor, diphacinone, dicumarol, chlorophacinone, bromadiolone, difenacoum, flocoumafen, and brodifacoum) in human blood by liquid chromatography–tandem mass spectrometry. After liquid–liquid extraction, the anticoagulant rodenticides were separated on an Eclipse Plus C18 column. Linearities were observed for each analyte in blood ranging from 0.5 to 50 ng/mL, with correlation coefficients over 0.99. The limits of detection ranged from 0.01 to 0.2 ng/mL, and the limits of quantification were 0.5 ng/mL for all analytes. The intraday and interday precisions were <15%, and accuracies ranged from 80.3% to 111.0%. This validated method with high sensitivity has been applied in three anticoagulant rodenticide poisoning cases and has been used successfully in monitoring blood concentrations for months.