Enantiomeric separation of methamphetamine and related analogs by capillary zone electrophoresis: intelligence study in routine methamphetamine seizures

A method for simultaneous enantiomeric separation of ephedrine, pseudoephedrine, and methamphetamine (MA) in a single run by simple capillary zone electrophoresis (CZE) with beta-cyclodextrin as a chiral selector is described. The effects of the buffer pH, phosphate concentration, beta-cyclodextrin concentration, voltage and temperature on the peak resolution were examined. Good enantiomeric resolution was attained for each analyte under our optimized conditions: 15 mM beta-cyclodextrin, 300 mM NaH2PO4 at pH 2.5 with an uncoated capillary (64.5 cm x 50 microm), applied potential at 20 kV and temperature at 30 degrees C. Ultraviolet (UV) detection at a fixed wavelength (200 nm) was employed using a diode array detector. Using phentermine as an internal standard, migration times for all analytes are reproducible within 0.16% for intra-day and 0.6% for inter-day runs. Application of this method to the analysis of confiscated drugs is discussed.     

Rapid analysis of caffeine in "smart drugs" and "energy drinks" by microemulsion electrokinetic chromatography (MEEKC)

A novel method based on microemulsion electrokinetic chromatography (MEEKC) with diode array detection (DAD) for rapid determination of caffeine in commercial and clandestine stimulants, known as "energy drinks" and "smart drugs", is described. Separations were carried out in 50 cm × 50 μm (ID) uncoated fused silica capillaries. The optimized buffer electrolyte was composed of 8.85 mM sodium tetraborate pH 9.5, SDS 3.3% (w/v), n-hexane 1.5% (v/v) and 1-butanol 6.6% (v/v). Separations were performed at a voltage of 20 kV. Sample injection conditions were 0.5 psi, 3 s. Diprofilline was used as internal standard. The determination of the analytes was based on the UV signal recorded at 275 nm, corresponding to the maximum wavelength of absorbance of caffeine, whereas peak identification and purity check was performed on the basis of the acquisition of UV radiation between 200 and 400 nm wavelengths. Under the described conditions, the separation of the compounds was achieved in 6 min without any interference from the matrix. Linearity was assessed within a caffeine concentration range from 5 to 100 μg/mL. The intra-day and inter-day precision values were below 0.37% for migration times and below 9.86% for peak areas. The present MEEKC method was successfully applied to the direct determination of caffeine in smart drugs and energy drinks.     

Simultaneous separation of different types of amphetamine and piperazine designer drugs by capillary electrophoresis with a chiral selector

The recent emergence of a new class of piperazine-type compounds has brought about the need for laboratory screening methods for both seized drugs and toxicological samples. These piperazine compounds, which include 1-benzylpiperazine (BZP) and 1-(3-trifluoromethylphenyl)piperazine (TFMPP), exhibit comparable physiological effects and can be substituted for the classic amphetamine-type drugs. We have optimized a chiral capillary electrophoresis (CE) separation that detects a set of 6 piperazine and 4 chiral amphetamine compounds in under 23 min using a 200 mM phosphate buffer at a pH = 2.8 with 20 mM hydroxypropyl- beta-cyclodextrin (HPbeta3CD). In addition to the above compounds, a series of "clandestine" BZP diHCl samples were also analyzed using this method to assess the ruggedness of the procedure. The novel CE separation was tailored to simultaneously detect these piperzine compounds in addition to amphetamine-type drugs. Distinct migration time and UV-spectral data were obtained for all compounds of interest.     

Rapid Separation of Organophosphate Pesticides using Micellar Electrokinetic Chromatography and Short‐end Injection,

Organophosphate (OP) pesticides are highly toxic substances and are frequently represented as poisons. In order to qualify and quantify the selected OP pesticides (methyl paraoxon, ethyl paraoxon, methyl parathion, fenitrothion, and ethyl parathion), micellar electrokinetic chromatography and short‐end injection were investigated. This is the first time that this combination has been used to separate OP pesticides. A capillary with 8.5 cm effective length was used, and the analytes were separated within 2.1 min. Separation conditions including buffer (type, pH, and concentration), sodium dodecyl sulfate concentration, and separation voltage were optimized. The limit of detection (LOD) was estimated in the range of 10–20 μM. The OP pesticides spiked in artificial saliva and drinking water gave superior peak profiles, and good average recoveries 95.6% and 62.3%, respectively. Overall, a rapid method with excellent resolution and efficiency was developed and successfully applied in the analysis of potential sample matrixes.     

Simultaneous analysis of gamma-hydroxybutyric acid, gamma-butyrolactone, and 1,4-butanediol by micellar electrokinetic chromatography

A micellar electrokinetic chromatography (MEKC) method was optimised for simultaneous analysis of gamma-hydroxybutyric acid (GHB), gamma-butyrolactone (GBL), and 1,4-butanediol (BD). Best conditions for separation and baseline stability were achieved using a carrier electrolyte comprising 30.0mM sodium barbital and 150.0mM sodium dodecyl sulphate (SDS) at pH 10.2. Calibration functions were linear, giving correlation coefficients (r(2)) >0.998 for the three target compounds. Limits of detection (LOD) defined as three times the noise, were 5.1mg/l, 0.34 and 0.25g/l for GHB, GBL and BD, respectively. The repeatability of migration times and peak areas, expressed as the R.S.D. (n = 9) was better than 0.41 and 3.05%, respectively. Some casework samples were analysed using the optimised conditions.     

Use of dynamically coated capillaries for the routine analysis of methamphetamine, amphetamine, MDA, MDMA, MDEA, and cocaine using capillary electrophoresis

A rapid, accurate, precise, reproducible, economical, and environmentally gentle method using capillary electrophoresis (CE) is presented for the routine analysis of methamphetamine, amphetamine, MDA, MDMA, MDEA, and cocaine in seized drugs. The methodology uses a 32 cm by 50 microm capillary (length to detector 23.5 cm) with a commercially available buffer kit and diode array UV detection. Dynamic coating of the capillary surface is accomplished by flushing with base for 1 min, a proprietary polycation for 1 min, and then a proprietary polyanion for 2 min. This approach provides a relatively high and stable electroosmotic flow (EOF), even at low pHs. The background electrolyte (BGE) contains 75 mM phosphate buffer (pH 2.5) with the same polyanion as above. Using this methodology, amphetamine, methamphetamine, MDA, MDMA, MDEA, and an internal standard (n-butylamphetamine) are baseline resolved in less than 5 min. The run-to-run migration time %RSDs and peak area %RSDs are typically <0.3% and <2.1%, respectively. The day-to-day and capillary-to-capillary migration time %RSDs are <1.5% and <2.1%, respectively. The %RSDs of the relative migration times compared with the internal standard on a day-to-day and capillary-to-capillary basis are <0.2% and <0.06%, respectively. The linear dynamic range using peak areas range from 0.003 to 0.10 mg/mL. The correlation coefficients are >0.9998, with all calibration curves passing at or near the origin. Similar data are obtained for cocaine and its internal standard henyltoloxamine. None of the compounds usually encountered in illicit samples interfere with the target compound (e.g., methamphetamine and cocaine) or the internal standard. Quantitative results for synthetic mixtures and seized exhibits are in good agreement with actual values, and also with results obtained from other techniques. The relatively high EOF for the dynamically coated capillary system allows for the screening of basic, acidic, and neutral adulterants in drug seizures; identification is facilitated by the use of automated UV library searches.     

Development of a capillary zone electrophoresis method including a factorial design and simplex optimisation for analysis of amphetamine, amphetamine analogues, cocaine, and heroin

A capillary zone electrophoresis (CZE) method was developed for the analysis of amphetamine and 13 amphetamine analogues. A full factorial design was used to screen for important design variables (i.e. carrier electrolyte concentration, pH, and separation temperature), and a modified simplex was employed in a final optimisation step. The resolution values of the target compounds were used as responses in the screening and optimisation phases. This approach made it possible to control the effects of the design variables on the separation of the target compounds. The best results were obtained using a 100mM Tris/phosphate buffer (pH 3.1) at a separation temperature of 10 degrees C, and the analysis time was 23 min under these conditions. After slight modification, the method also enabled baseline resolution of the most commonly encountered amphetamine derivatives, as well as cocaine and heroin, within 7 min. There was a linear relationship between peak area and concentration for all substances, with correlation coefficients in the range of 0.9975-0.9999. Moreover, the technique was repeatable and exhibited relative standard deviation (R.S.D.) values in the ranges of 0.01-0.11% and 0.54-1.60% for relative migration time and corrected peak area, respectively. Lastly, the method was successfully applied to analyse street samples.     

A rapid and convenient LC/MS method for routine identification of methamphetamine/dimethylamphetamine and their metabolites in urine

A rapid and sensitive LC/MS method was developed for the simultaneous analysis of N,N-dimethylamphetamine (DMA), N,N-dimethylamphetamine N-oxide (DMANO), methylamphetamine (MA) and amphetamine (A) in urine samples. Employing an Alltech C18 column for solid phase extraction followed by LC/MS analysis using an Alltech Platinum EPS C18 column with a mixture of ammonium formate (0.01 M, pH 3) and acetonitrile (77:23, v/v) as mobile phase at a flow rate of 0.2 mL/min, simultaneous identification and quantitation of A, MA, DMA and DMANO in urine can be achieved using a 5-min chromatographic run. The calibration ranges were 0.10-3.0 micro g/mL for DMANO, 0.05-3.0 micro g/mL for DMA and 0.05-5.0 micro g/mL for both MA and A. The intra-, inter-day precision and accuracy for all analytes, spiked at three different concentrations in quality control samples, were in the ranges of 1.7-8.6, 4.1-10.0, -11.6 to 12.9%, respectively. The newly developed method was applied to the analysis of urine samples obtained from 118 suspected MA/DMA abusers, with the presence of MA confirmed in their urine samples under the drug-use surveillance program. Of these 118 samples, 43 were found to contain DMANO and 11 with both DMANO and DMA.     

Identification of human urine stains by HPLC analysis of 17-ketosteroid conjugates

A new method for identifying human urine stains utilizing high-performance liquid chromatographic (HPLC) analysis of five major 17-ketosteroid conjugates: dehydroepiandrosterone sulfate, etiocholanolone sulfate, etiocholanolone glucuronide, androsterone sulfate, and androsterone glucuronide was examined. Samples of urine stains were extracted with borate buffer solution (pH 9.3) and the extracts were applied onto a Sep-Pak tC18 cartridge. The analytes were eluted from the cartridge with methanol. The eluates were prelabeled with 2,4-dinitrophenylhydrazine in trichloroacetic acid-benzene solution and were separated by HPLC on a reversed-phase ODS column using a mobile phase of 80% methanol in a buffer consisting of 25 mM sodium acetate in 2% acetic acid. The eluates were monitored by a spectrophotometer at 380 nm. While all five 17-ketosteroid conjugates were clearly detected in the human urine stain samples, traces of only some of these conjugates were detected in the animal samples. Therefore, the presence of all five 17-ketosteroid conjugates indicated human specificity. In addition to the above finding, the properties of those five 17-ketosteroid conjugates were confirmed by electrospray ionization liquid chromatography-mass spectrometry (ESI-LC-MS).     

Simultaneous analysis of six amphetamines and analogues in hair, blood and urine by LC-ESI-MS/MS. Application to the determination of MDMA after low ecstasy intake

A rapid and sensitive method using LC-MS/MS triple stage quadrupole for the determination of traces of amphetamine (AP), methamphetamine (MA), 3,4-methylenedioxyamphetamine (MDA), 3,4-methylenedioxymethamphetamine (MDMA, "ecstasy"), 3,4-methylenedioxyethamphetamine (MDEA), and N-methyl-1-(3,4-methylenedioxyphenyl)-2-butanamine (MBDB) in hair, blood and urine has been developed and validated. Chromatography was carried out on an Uptisphere ODB C(18) 5 microm, 2.1 mm x 150 mm column (Interchim, France) with a gradient of acetonitrile and formate 2 mM pH 3.0 buffer. Urine and blood were extracted with Toxitube A (Varian, France). Segmented scalp hair was treated by incubation 15 min at 80 degrees C in NaOH 1M before liquid-liquid extraction with hexane/ethyl acetate (2/1, v/v). The limits of quantification (LOQ) in blood and urine were at 0.1 ng/mL for all analytes. In hair, LOQ was <5 pg/mg for MA, MDMA, MDEA and MBDB, at 14.7 pg/mg for AP and 15.7 pg/mg for MDA. Calibration curves were linear in the range 0.1-50 ng/mL in blood and urine; in the range 5-500 pg/mg for MA, MDMA, MDEA and MBDB, and 20-500 pg/mg for AP and MDA. Inter-day precisions were <13% for all analytes in all matrices. Accuracy was <20% in blood and urine at 1 and 50 ng/mL and <10% in hair at 20 and 250 pg/mg. This method was applied to the determination of MDMA in a forensic case of single administration of ecstasy to a 16-year-old female without her knowledge during a party. She suffered from hyperactivity, sweating and agitation. A first sample of urine was collected a few hours after (T+12h) and tested positive to amphetamines by immunoassay by a clinical laboratory. Blood and urine were sampled for forensic purposes at day 8 (D+8) and scalp hair at day 60 (D+60). No MDMA was detected in blood, but urine and hair were tested positive, respectively at 0.42 ng/mL and at 22 pg/mg in hair only in the segment corresponding to the period of the offence, while no MDA was detectable. This method allows the detection of MDMA up to 8 days in urine after single intake.     

Optimization of a simple method for the chiral separation of methamphetamine and related compounds in clandestine tablets and urine samples by beta-cyclodextrine modified capillary electrophoresis: a complementary method to GC-MS

The chiral separation of (+/-)-methamphetamine, (+/-)-methcathinone, (+/-)-ephedrine and (+/-)-pseudoephedrine by means of beta-cyclodextrine modified capillary electrophoresis is described. The distribution of enantiomers in clandestine tablets and urine samples were identified. Several electrophoretic parameters such as the concentration of beta-cyclodextrin, temperature, the applied voltage and the amount of organic solvent required for successful separation were optimized. The method, as described herein, represents a good complementary method to GC-MS for use in forensic and clinical analysis.     

Analysis of dimethylamphetamine and its metabolites in human urine by liquid chromatography-electrospray ionization-mass spectrometry with direct sample injection

An analytical method to identify and determine dimethylamphetamine (DMA) and its metabolites in human urine was developed with liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS) involving the direct injection of a urine sample. The urine samples were directly injected by using a gel permeation column, whose stationary phase was polyvinyl alcohol with a small amount of a carboxyl group, so DMA and its metabolites were analyzed rapidly and simply without pretreatment such as extraction, concentration and derivatization. DMA and its metabolites were identified in drug-free human urine spiked with 1 microg of DMA, dimethylamphetamine N-oxide (DMANO) and methamphetamine (MA), and 3 microg of amphetamine (AM) in 1 ml of urine under the full-scan mode. Under the selected ion monitoring (SIM) mode, the limits of detection (signal-to-noise ratio=5) for DMA, DMANO, MA and AM were 20, 20, 20 and 60 ng in 1 ml of urine, respectively. This method was applied to the identification and determination of DMA and its metabolites in urine samples of 10 DMA abusers. The concentrations of DMANO were higher than those of unchanged DMA in all urine samples; thus, DMANO is considered to be a useful metabolite as an indicator to prove DMA intake.     

Detection and validated quantification of 21 benzodiazepines and 3 "z-drugs" in human hair by LC-MS/MS

A method for detection and quantification of 21 benzodiazepines and the pharmacologically related "z-drugs" in human hair samples was developed and fully validated using liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS). After methanolic and methanolic/aqueous extraction, the analytes were separated using two different LC-MS systems (AB Sciex 3200 QTRAP and AB Sciex 5500 QTRAP). Separation columns, mobile phases and MS modes for both systems were: Phenomenex Kinetex, 2.6 μm, 50/2.1; 5mM ammonium formate buffer pH 3.5/methanol, total flow 0.75 mL/min; electrospray ionization (ESI), multiple reaction monitoring (MRM), information dependent acquisition (IDA), enhanced product ion scan (EPI). The assays were found to be selective for the tested compounds (alprazolam, 7-aminoclonazepam, 7-aminoflunitrazepam, bromazepam, chlordiazepoxide, clonazepam, N-desalkylflurazepam, diazepam, flunitrazepam, flurazepam, alpha-hydroxymidazolam, lorazepam, lormetazepam, midazolam, nitrazepam, nordazepam, oxazepam, phenazepam, prazepam, temazepam, triazolam, zaleplon, zolpidem and zopiclone), all validation criteria were in the required ranges according to international guidelines, except for bromazepam. Matrix effects, and process efficiencies were in the acceptable ranges evaluated using the post-extraction addition approach. Lower limits of quantification were between 0.6 and 16 pg/mg of hair. The LC-MS/MS assay has proven to be applicable for determination of the studied analytes in human hair in numerous authentic cases (n=175).     

Screening for the presence of drugs in serum and urine using different separation modes of capillary electrophoresis

Capillary electrophoresis (CE) is a modern separation technique that has some distinct advantages for toxicological analysis, such as a high efficiency, fast analysis, flexibility, and complementary separation mechanisms to chromatographic methods. CE can be applied in various modes, which each have a different separation mechanism or selectivity. The most common mode is capillary zone electrophoresis (CZE), in which charged analytes migrate in a buffer under the influence of an electric field. In micellar electrokinetic chromatography (MEKC), micelles are added to the buffer which interact with the analytes. MEKC can also be used for the separation of neutral compounds. In non-aqueous CE (NACE), the aqueous buffer is replaced by a background of electrolytes in organic solvents. A sample that needs to be screened can easily be analyzed subsequently by these CE modes using the same instrumentation.The aim of the study was to develop procedures for the analysis of basic and acidic drugs in serum and urine using CZE, MEKC, and NACE. A test mixture that consisted of six basic and six acidic compounds was used to study the separation behavior of five CE methods. The results showed that three methods (based on CZE, MEKC, and NACE) were suitable for the analysis of basic compounds and three methods (based on CZE and MEKC) for the analysis of acidic compounds.For the extraction of analytes from serum and urine, a solid-phase extraction (SPE) and a liquid-liquid extraction (LLE) method were compared. Both SPE and LLE methods provided clean extracts after extraction of the basic compounds from serum and urine. The extracts of acidic compounds contained more matrix interferences, especially for urine. The SPE method had some advantages compared to LLE, as it lead to cleaner extracts and higher peaks, and as it elutes basic and acidic compounds in one fraction.The potentials and pitfalls of the various methods for screening purposes in analytical toxicology are discussed.     

Application of dispersive liquid-liquid microextraction and CE with UV detection for the chiral separation and determination of the multiple illicit drugs on forensic samples

A new method was developed for pre-concentration, chiral separation and determination of multiple illicit drugs on forensic samples using dispersive liquid-liquid microextraction (DLLME) and capillary electrophoresis (CE) with Ultra Violet (UV) detection. The method was based on the formation of tiny droplets of an organic extractant in the prepared sample solution using water-immiscible organic solvent (chloroform) dissolved in water-miscible organic dispersive solvent (isopropyl alcohol). The organic phase, which extracted heroin, DL-methamphetamine, DL-3, 4-methylenedioxymethamphetamine and dl-ketamine from the prepared sample solution, was separated by centrifuging. The sedimented phase was transferred into a small volume CE auto-sampler vial with 10 μL of 1% HCl methanol solution and evaporated to dryness. The residue was reconstituted in lidocaine hydrochloride aqueous solution (internal standard) and introduced by electrokinetic injection into CE. Parameters affecting extraction efficiency were investigated and optimized. Under optimum conditions, linearity of the method was 0.15-6500 μg/L for all target analytes. The LODs (S/N=3) were 0.05-0.20 μg/L. Excellent repeatability (RSD ≤ 4.4%, n=5) was achieved. The feasibility of this method was demonstrated by analyzing spiked forensic samples. To our knowledge, it is the first time to combine DLLME with CE for chiral separation and determining illicit drugs on forensic samples.     

Alternative direct-to-amplification cell lysis techniques for forensically relevant non-sperm cells

While efforts have been made to reduce the pervasive backlog of sexual assault evidence collection kits, the actual laboratory process remains very time-consuming due to the requirement of a differential lysis step before DNA purification, as well as intricate mixture analysis towards the end of the DNA workflow. Recently, an alternative, direct-to-amplification sperm lysis method (using 1 M NaOH) was identified. However, a direct cell lysis method for non-sperm cells has not been identified yet. Thus, the primary objective of this work was to find an alternative method that is quick, inexpensive, and does not require multiple purification steps for the lysis of non-sperm cells in sexual assault samples. In this study, vaginal swab samples were lysed with the control method, prepGEM™, as well as six alternative reagents: alkaline buffer with 25–200 mM NaOH, high-salt stain extraction buffer, modified radioimmunoprecipitation assay (RIPA) buffer, mammalian protein extraction reagent (M-PER™), digitonin buffer, and urea/thiourea buffer. Quantification using Quantifiler® Trio of vaginal and semen lysates revealed that the alkaline (25 mM NaOH) and M-PER™ methods were efficient for the lysis of vaginal epithelial cells without substantial sperm cell lysis. Following quantification, analysis of STR profiles from vaginal lysates revealed that the M-PER™ method showed promising results across all metrics examined, including the percentage of detected STR alleles, mean peak heights, peak height ratio, and interlocus balance. Thus, this method was recommended as an alternative to the traditional differential lysis method for non-sperm cells given its ability to produce amplification-ready lysates without any DNA purification step.     

Optimized conditions for simultaneous determination of opiates, cocaine and benzoylecgonine in hair samples by GC--MS

The present paper describes a qualitative and quantitative method for the simultaneous detection of opiates, cocaine and benzoylecgonine from human hair samples. Every step of the analytical procedure was studied to find the optimized conditions. Nine different incubation systems were examined. The influence of different pH values of samples on the isolation of analytes from the incubation media by Bond Elut cartridges and the stability of the compounds of interest in the different incubation media and conditions were investigated. The extracting power of different incubation media was studied as well. The phosphate buffer 0.1 N at pH 5 was chosen as the extraction medium in an optimized procedure for simultaneous determination of opiates, cocaine and benzoylecgonine in hair samples. The method developed was validated. Recoveries were 90% for morphine (M), 81% for 6-monoacetylmorphine (6-AM), 90% for codeine (CD), 86% for cocaine (C) and 90% for benzoylecgonine (BE). Relative standard deviation for inter-day precision was better than 12%. The limits of detection resulted as 0.05 ng/mg for M and C, as 0.08 for 6-AM and as 0.2 ng/mg for BE. Forty hair samples collected from drug abusers admitted to centers for detoxification treatment were analyzed obtaining 23 positive results for opiates and/or cocaine. Twelve hair specimens longer than 10 cm were analyzed following a sectional approach. In the six positive cases, it was interesting to find that the 6-AM/M ratio generally decreased for each sample from the proximal segment to the distal segments. Moreover, the 6-AM/M ratio was generally lower than 1 in the intermediate and distal segments.     

Simultaneous analysis of six amphetamines and analogues in hair, blood and urine by LC-ESI-MS/MS: Application to the determination of MDMA after low Ecstasy intake

A rapid and sensitive method using LC-MS/MS triple stage quadrupole for the determination of traces of amphetamine (AP), methamphetamine (MA), 3,4-methylenedioxyamphetamine (MDA), 3,4-methylenedioxymethamphetamine (MDMA, “ecstasy”), 3,4-methylenedioxyethamphetamine (MDEA), and N-methyl-1-(3,4-methylenedioxyphenyl)-2-butanamine (MBDB) in hair, blood and urine has been developed and validated. Chromatography was carried out on an Uptisphere ODB C₁₈ 5 μm, 2.1 mm × 150 mm column (Interchim, France) with a gradient of acetonitrile and formate 2 mM pH 3.0 buffer. Urine and blood were extracted with Toxitube A^® (Varian, France). Segmented scalp hair was treated by incubation 15 min at 80 °C in NaOH 1 M before liquid–liquid extraction with hexane/ethyl acetate (2/1, v/v). The limits of quantification (LOQ) in blood and urine were at 0.1 ng/mL for all analytes. In hair, LOQ was <5 pg/mg for MA, MDMA, MDEA and MBDB, at 14.7 pg/mg for AP and 15.7 pg/mg for MDA. Calibration curves were linear in the range 0.1–50 ng/mL in blood and urine; in the range 5–500 pg/mg for MA, MDMA, MDEA and MBDB, and 20–500 pg/mg for AP and MDA. Inter-day precisions were <13% for all analytes in all matrices. Accuracy was <20% in blood and urine at 1 and 50 ng/mL and <10% in hair at 20 and 250 pg/mg. This method was applied to the determination of MDMA in a forensic case of single administration of ecstasy to a 16-year-old female without her knowledge during a party. She suffered from hyperactivity, sweating and agitation. A first sample of urine was collected a few hours after (T + 12 h) and tested positive to amphetamines by immunoassay by a clinical laboratory. Blood and urine were sampled for forensic purposes at day 8 (D + 8) and scalp hair at day 60 (D + 60). No MDMA was detected in blood, but urine and hair were tested positive, respectively at 0.42 ng/mL and at 22 pg/mg in hair only in the segment corresponding to the period of the offence, while no MDA was detectable. This method allows the detection of MDMA up to 8 days in urine after single intake.     

Achiral and chiral quantification of methamphetamine and amphetamine in human urine by semi-micro column high-performance liquid chromatography and fluorescence detection

In this paper, miniaturized achiral and chiral high-performance liquid chromatographic procedures for the determination of methamphetamine and amphetamine in human urine are described. After a simple pretreatment of human urine (i.e., 10 microL of urine or diluted urine were acidified and dried-up under N2 at room temperature) and fluorescence derivatization with 4-(4,5-diphenyl-1H-imidazol-2-yl)-benzoyl chloride under mild conditions (pH 9.0, 10 min at room temperature), the derivatives were isocratically separated on a semi-micro ODS column with Tris-HCl buffer (0.1 M, pH 7.0): acetonitrile (45 + 55 v/v) at a flow rate of 0.2 mL/min or their enantiomers were separated on a semi-micro OD-RH column with sodium hexafluorophosphate (0.3 M aq.): acetonitrile (44 + 56 v/v) at a flow rate of 0.1 mL/min as the mobile phase. Wide-ranged calibration curves were obtained with detection limits for the achiral and chiral analyses in the atto and femtomol levels, respectively, per injected volume. Satisfactory within- and between-day reproducibility data were obtained with both the methods with the highest relative standard deviation being 9.6%. The methods were applied to the determination of methamphetamine and amphetamine in human urine samples and the concentrations determined by the two methods were well correlated (r = 0.994).     

Optimization of the separation of organic explosives by capillary electrophoresis with artificial neural networks

The separation of 12 explosives by capillary electrophoresis was optimized with the aid of artificial neural networks (ANNs). The selectivity of the separation was manipulated by varying the concentration of sodium dodecyl sulfate (SDS) and the pH of the electrolyte, while maintaining the buffer concentration at 10 mM borate. The concentration of SDS and the electrolyte pH were used as input variables and the mobility of the explosives were used as output variables for the ANN. In total, eight experiments were performed based on a factorial design to train a variety of artificial neural network architectures. A further three experiments were required to train ANN architectures to adequately model the experimental space. A product resolution response surface was constructed based on the predicted mobilities of the best performing ANN. This response surface pointed to two optima; pH 9.0-9.1 and 60-65 mM SDS, and pH 8.4-8.6 and 50-60 mM SDS. Separation of all 12 explosives was achieved at the second optimum. The separation was further improved by changing the capillary to an extended cell detection window and reducing the diameter of the capillary from 75 microm to 50 microm. This provided a more efficient separation without compromising detection sensitivity.