Cross-examination of liquid-liquid extraction (LLE) and solid-phase microextraction (SPME) methods for impurity profiling of methamphetamine

Impurities in 48 methamphetamine (MA) samples were analyzed by liquid-liquid extraction (LLE) and headspace solid-phase microextraction (HS-SPME) methods. MPS-2 autosampler was used to improve reproducibility of SPME method, and nonadecane (C(19)) diluted with potassium bromide (KBr) powder was used as an internal standard for standardizing retention time. Impurities identified by SPME method showed different patterns compared with LLE method. Non-volatile impurities like methamphetamine dimer were not identified by SPME method, but some volatile impurities like diphenylketone, caprolactam and lots of unknowns were identified only by SPME method. 1-Phenyl-2-propanone (P2P), 1-phenyl-2-propanol and benzylcyanide peaks could be discriminated clearly by SPME method without interference of amphetamine, an artifact originates from MA degradation. Differences in the impurity patterns resulted in different clustering results. When 48 MA samples were classified into 5 LLE and 5 SPME clusters, cross-matching of the clusters resulted in 8 sub-clusters. It shows that combination of the different extraction methods can distinguish the differences which cannot be distinguished by LLE or SPME method alone, and can improve reliability of the profiling results.     

Contribution of thermal desorption and liquid-liquid extraction for identification and profiling of impurities in methamphetamine by gas chromatography-mass spectrometry

Impurity profiling of methamphetamine (MA) using thermal desorption (TD) and gas chromatography-mass spectrometry (GC-MS) was examined. Using TD/GC-MS, impurities were extracted and separated under various conditions. Optimal chromatograms were obtained when a 20 mg MA sample was extracted at 120 degrees C for 3 min using a TD instrument, followed by separation of the extracts using a non-polar capillary column coated with (5%phenyl)-methylpolysiloxane. MA samples from nine different batches were analyzed under optimized conditions. Compounds related to the structure of MA, such as benzaldehyde, benzyl alcohol, amphetamine, cis- and trans-1,2-dimethyl-3-phenylaziridine, dimethylamphetamine, and N-acetylephedrine, were detected in the chromatograms without any laborious extraction procedure. Compounds such as ethanol, diethyl ether, and acetic acid, which are considered reagents and solvents for MA synthesis, were also detected in some of the chromatograms. The numbers and intensities of the peaks detected were different among the samples. Impurity profiling of MA using TD was compared with that using liquid-liquid extraction (LLE). Better reproducibility of peak areas was obtained using LLE, whereas higher intensities and numbers of peaks were detected using TD. Solvents were extracted more effectively using TD. The nine batches of MA were classified using both extraction procedures. The nine batches were divided roughly into two groups using data from LLE. Subsequently, the groups were classified in detail using data from TD. TD can be used to provide supplemental information for LLE, and the combination of these extraction methods can be helpful for impurity profiling of MA.     

Development of microwave-assisted extraction procedure for organic impurity profiling of seized 3,4-methylenedioxymethamphetamine (MDMA)

Abstract: Organic impurity profiling of seized 3,4‐methylenedioxymethamphetamine (MDMA) tablets aims to link tablets to common production sources. Conventionally, organic impurities are extracted from tablets using a liquid–liquid extraction (LLE) procedure prior to analysis by gas chromatography–mass spectrometry (GC‐MS). In this research, the development of an alternative microwave‐assisted extraction/headspace solid‐phase microextraction (MAE/HS‐SPME) procedure is described. The optimal procedure used phosphate buffer (1 M, pH 8), with an HS‐SPME extraction temperature of 70°C for 40 min, using a divinylbenzene/Carboxen?/polydimethylsiloxane (DVB/CAR/PDMS) fiber. Impurities were extracted from seized MDMA exhibits using the MAE/HS‐SPME procedure, as well as HS‐SPME alone, and a conventional LLE procedure. The HS‐SPME procedure was deemed to be the most practical because of the affordability and need for less analyst involvement. Although the LLE was limited in the number of impurities extracted, the procedure is still useful for the extraction of less volatile impurities that are not extracted by HS‐SPME.     

Use of headspace solid-phase microextraction (HS-SPME) in hair analysis for organic compounds

Headspace solid phase microextraction (HS-SPME) has advantages of high purity of the extract, avoidance of organic solvents and simple technical manipulation and can be used in combination with gas chromatography-mass spectrometry (GC-MS) in the hair analysis of a number of drugs. HS-SPME coupled with the hydrolysis of the hair matrix by 4% sodium hydroxide in the presence of excess sodium sulphate and of a suitable internal standard proved to be a convenient one-step method for the measurement of many lipophilic basic drugs such as nicotine, amphetamine derivatives, local anaesthetics, phencyclidine, ketamine, methadone, diphenhydramine, tramadol, tricyclic antidepressants and phenothiazines. Detection limits were between 0.05 and 1.0 ng/mg. From spiked 10-mg hair samples absolute recoveries between 0.04 and 5.7% were found. These recoveries decreased considerably if larger sample amounts were used, perhaps due to increased drug solubility in the aqueous phase or to elevated viscosity in the presence of dissolved hair proteins. Because of the phenolic hydroxyl group a change of pH after alkaline hair digestion (by adding excess orthophosphoric acid) was necessary for the detection of delta 9-tetrahydrocannabinol (delta 9-THC), cannabinol (CBN) and cannabidiol (CBD) by HS-SPME. Nevertheless, the detection limits were such that only CBN could be detected in hair of a consumer. Clomethiazole, a compound hydrolysed in alkali, was measured by HS-SPME after extraction with aqueous buffer. The detection limit was 0.5 ng/mg. Cocaine could not be detected by HS-SPME. The application of HS-SPME to hair samples from several forensic and clinical cases is described.     

The application of amino acid racemization in the acid soluble fraction of enamel to the estimation of the age of human teeth

The main objectives of the European project "Collaborative Harmonization of Methods for Profiling of Amphetamine Type Stimulants" (CHAMP) funded by the sixth framework programme of the European Commission, included the harmonization of MDMA profiling methods and the creation of a common database in a drug intelligence perspective. In the preliminary stages of this project, the participating laboratories analysed the physical characteristics, the chemical composition and the organic impurities of MDMA tablets, using the previously harmonized methods. The aim of the present work was to apply statistical treatments to the recorded data in order to evaluate their potential in the fight against drug trafficking. Comparable working procedures were applied on the different types of data. The first part of this article deals with organic impurities data, while the second part focuses on the potential of the physical characteristics. Organic impurities data were recorded by a harmonized Gas Chromatography/Mass Spectrometry (GC/MS) method previously developed. Statistical analysis provided a selection of pertinent variables among the 46 organic impurities identified in the chromatograms. Correlation coefficients were used to yield separation between populations of samples coming from the same synthesis batch and samples coming from different batches. It was shown that correlation measurements based on Pearson and cosine functions applied to the data pre-treated by normalisation to the sum of peak responses followed by the square root provided an excellent discrimination between the two populations. The statistical methods applied to organic impurities profiles proved to be excellent techniques to differentiate samples from different batches and to highlight operational links between samples.     

Screening for the presence of drugs in serum and urine using different separation modes of capillary electrophoresis

Capillary electrophoresis (CE) is a modern separation technique that has some distinct advantages for toxicological analysis, such as a high efficiency, fast analysis, flexibility, and complementary separation mechanisms to chromatographic methods. CE can be applied in various modes, which each have a different separation mechanism or selectivity. The most common mode is capillary zone electrophoresis (CZE), in which charged analytes migrate in a buffer under the influence of an electric field. In micellar electrokinetic chromatography (MEKC), micelles are added to the buffer which interact with the analytes. MEKC can also be used for the separation of neutral compounds. In non-aqueous CE (NACE), the aqueous buffer is replaced by a background of electrolytes in organic solvents. A sample that needs to be screened can easily be analyzed subsequently by these CE modes using the same instrumentation.The aim of the study was to develop procedures for the analysis of basic and acidic drugs in serum and urine using CZE, MEKC, and NACE. A test mixture that consisted of six basic and six acidic compounds was used to study the separation behavior of five CE methods. The results showed that three methods (based on CZE, MEKC, and NACE) were suitable for the analysis of basic compounds and three methods (based on CZE and MEKC) for the analysis of acidic compounds.For the extraction of analytes from serum and urine, a solid-phase extraction (SPE) and a liquid-liquid extraction (LLE) method were compared. Both SPE and LLE methods provided clean extracts after extraction of the basic compounds from serum and urine. The extracts of acidic compounds contained more matrix interferences, especially for urine. The SPE method had some advantages compared to LLE, as it lead to cleaner extracts and higher peaks, and as it elutes basic and acidic compounds in one fraction.The potentials and pitfalls of the various methods for screening purposes in analytical toxicology are discussed.     

Comparison of molecularly imprinted solid-phase extraction (MISPE) with classical solid-phase extraction (SPE) for the detection of benzodiazepines in post-mortem hair samples

This preliminary study compares the benzodiazepine results for 10 post-mortem scalp hair samples using a classical solid-phase extraction (SPE) and a molecularly imprinted solid-phase extraction (MISPE) system. The hair samples selected for testing were from drug-related deaths where a positive benzodiazepine blood result was obtained. Samples were decontaminated with 0.1% sodium dodecyl sulfate, distilled water and dichloromethane, incubated overnight in methanol/25% aqueous ammonium hydroxide (20:1), extracted by SPE or MISPE and subsequently analysed by liquid chromatography-tandem mass spectrometry (LC-MS-MS). Both extraction methods detected diazepam, nordiazepam, oxazepam, temazepam and nitrazepam in the samples. Diazepam was detected in a greater number of samples using MISPE due to both its lower limit of detection (LOD) and higher extraction recovery as a result of excellent molecular recognition of the template (diazepam) imparted by the imprinting process. The selective recognition of two diazepam analogues, nordiazepam and oxazepam, was demonstrated using MISPE since they were also detected in a greater number of samples. In contrast, another diazepam analogue, temazepam, was detected in a greater number of samples using SPE since the LOD using this extraction was lower than with MISPE. Nitrazepam was detected in one sample using both extraction methods. Overall the MISPE and SPE hair results were in good qualitative agreement. For the samples, where both extraction methods detected nordiazepam, temazepam and oxazepam, the concentrations were always higher for SPE. This is probably due to the MIP procedure producing extracts with fewer matrix interferences than the extracts produced using the classical SPE method. MISPE could be used as a complementary method to classical SPE for the analysis of benzodiazepine positive hair samples collected from chronic users.     

Identification of impurities and the statistical classification of methamphetamine using headspace solid phase microextraction and gas chromatography-mass spectrometry

The profiling of impurities in methamphetamine (MA) using headspace solid phase microextraction (HS-SPME) and gas chromatography-mass spectrometry (GC-MS) is described. The extraction of the impurities with an SPME fiber was examined under varying conditions. Optimal chromatograms were obtained when a 50 mg MA sample at 85 degrees C for 30 min was extracted using a fiber coated with divinylbenzene/carboxen/polydimethylsiloxane. MA samples from nine different origins were analyzed under optimized extraction conditions. Compounds related to MA such as benzaldehyde, benzyl alcohol, amphetamine, benzyl methyl ketone, cis- and trans-1,2-dimethyl-3-phenylaziridine, dimethylamphetamine, N-acetylamphetamine, N-acetylmethamphetamine and N-formylmethamphetamine were detected in the chromatograms. Trace amounts of ethanol, diethyl ether and acetic acid were also detected in some of the chromatograms. The numbers and intensities of the peaks detected were different, depending on the sample. After the areas of the eight principal peaks were converted to their square root and logarithm, similarities among the samples were evaluated by Euclidian distance, cosine distance and correlation coefficient. The results showed that a combination of logarithmic conversion and cosine distance was the most suitable for discriminating and classifying the samples. HS-SPME/GC-MS is a simple and effective method for the extraction and identification of impurities. The present method, in combination with an appropriate statistical analysis, would be useful for developing a profile of impurities in MA.     

Automated headspace solid-phase microextraction and capillary gas chromatography analysis of ethanol in postmortem specimens

Solid-phase microextraction (SPME) is a relatively new solventless sample preparation technique that allows simultaneous sampling, extraction, pre-concentration, and introduction of analytes from a sample matrix in a single procedure. This methodology has been used for the analysis of several drugs of forensic toxicology interest including volatile compounds. This paper describes a methodology for analysis of ethanol and other volatile compounds using automatic headspace solid-phase microextraction (HS-SPME) and capillary gas chromatography in postmortem specimens. The methodology was initially developed using standard solutions of acetaldehyde, acetone, methanol, and ethanol. Isobutanol was used as internal standard. Postmortem samples of blood, urine, and vitreous humor were obtained during medico-legal autopsies. To date, there are no published paper regarding alcohol analysis in vitreous humor specimens using HS-SPME and limited literature analyzing blood and urine samples. HS-SPME analysis showed that, under optimized conditions, ethanol and isobutanol (internal standard) were well-separated from other volatile compounds such as acetaldehyde, acetone, and methanol considered to be potential interferents in ethanol analysis. The calibration curves for each volatile compound demonstrated good linearity throughout the concentration range from 0.001 to 1.0 g/dl and the detection limit of ethanol in the studied specimens was approximately 0.0001 g/dl.     

Determination of venlafaxine in post-mortem whole blood by HS-SPME and GC-NPD

Venlafaxine is a phenethylamine derivative widely prescribed for the treatment of depression which inhibits both serotonin and norepinephrine reuptake (SNRI). In treatment with antidepressants of patient with depression and other psychiatric disorders there is also increased risk of suicidal thought and behaviour. Several lethal intoxications involving venlafaxine usually among psychotic patients have been reported in the literature. Sample preparation is of the greatest significance for a successful toxicological analysis. The development of simple, effective and rapid extraction procedures of drugs from post-mortem biological samples is a challenge. Headspace-solid phase microextraction (HS-SPME) offers significant advantages such as simplicity, low cost, compatibility with analytical systems, automation and solvent-free extraction. The aim of our work was the optimization of a HS-SPME procedure for the determination of venlafaxine in post-mortem biological samples by gas chromatography (GC) with nitrogen-phosphorous detection (NPD). Venlafaxine was extracted on 100 μm Polydimethylsiloxone Coating-Red (PDMS) SPME fiber and determined by GC-NPD. Salt addition, extraction temperature, preheating and extraction time were optimized to enhance the recovery of the extraction from aqueous solution spiked with venlafaxine. Finally the developed procedure was applied to post-mortem biological samples of a fatally poisoned woman by venlafaxine. The drug was quantified in post-mortem blood gastric and oesophagus contents of the deceased woman. A simple and rapid procedure using HS-SPME was developed for sample preparation of venlafaxine in post-mortem biological samples prior to GC-NPD determination. Validation data was satisfactory, thus enabling application in the toxicological analysis of forensic samples.     

The comparison of toluene determination between headspace-solid phase microextraction and headspace methods in glue-sniffer's blood and urine samples

An accurate and simple method was developed to determine the level of toluene in urine and blood quantitatively by using the gas chromatography/mass spectrometry (GC/MS) with headspace--solid phase microextraction (HS-SPME) technique. An assembly of SPME with a replaceable extraction fiber, coated with 100 microm polydimethylsiloxane, was used. The detection limit of toluene in blood and urine with HS-SPME technique was 10 times higher than that with headspace (HS) technique. To compare the HS-SPME with HS technique for the determination of toluene in biological fluids, blood and urine samples from glue sniffers were analyzed by both methods. The level of toluene by the two techniques was highly correlated: the correlation coefficient (r2) between the two sets of values were 0.98 and 0.96 in urine and blood, respectively.     

应用DNA工作站进行批量血斑STR分型的研究

目的建立对大批量血斑样品PCR-STR基因分型检测的自动化新方法。方法应用自动化DNA工作站改良优化Chelex-100法和DNAIQ磁珠法的实验条件,建立两种批量血斑的自动化DNA提取方法;筛选确定PCR-STR反应体系的构建和PCR-STR产物测序电泳分析前处理程序。结果1104份血斑样品经Chelex-100法批量提取、Profiler Plus试剂盒扩增均一次检出9个STR基因座,定量PCR测定模板浓度均值为0.43ng/ml,荧光检测信号在200~800RFU之间;对其中114份血斑样品用DNAIQ磁珠法批量提取、同试剂盒扩增均一次检出9个STR基因座,定量PCR测定模板浓度均值为0.7ng/ml,荧光检测信号在1000~2000RFU之间;对其中50份血斑进行自动和手动Chel-ex-100检验法比较,成功率分别为100%和98%,且前者等位基因峰高信号更均衡。结论本文建立的自动化DNA工作站批量检测方法,在成功率、稳定性、均一性等方面具有优势。     

Development of a harmonised method for the profiling of amphetamines: IV. Optimisation of sample preparation

The suitability of liquid-liquid extraction (LLE) and solid-phase extraction (SPE) for the preparation of impurity extracts intended for gas chromatographic profiling analyses of amphetamine were evaluated. Both techniques were optimised with respect to the extraction of selected target compounds by use of full factorial designs in which the variables affecting the performance were evaluated. Test samples consisted of amphetamine synthesised by the Leuckart reaction, by reductive amination of benzyl methyl ketone and by the nitrostyrene route. The performance of LLE and SPE were comparable in terms of repeatability and recovery of the target compounds. LLE was considered the better choice for the present harmonised amphetamine profiling method due to the lack of information on the long-term stability of SPE columns.     

Comparison and classification of methamphetamine seized in Japan and Thailand using gas chromatography with liquid-liquid extraction and solid-phase microextraction

Methamphetamine (MA) is one of the most frequently abused drugs worldwide. The aim of this study is to improve the analytical method for profiling MA impurity in order to compare and classify MA crystals seized in different countries and to investigate the relationships between seizures. To compare MA samples seized in Japan and Thailand, the following analytical method was adopted. A 50mg sample of MA.HCl was dissolved in 1ml of buffer solution (four parts 0.1M phosphate buffer, pH 7.0, and one part 10% Na(2)CO(3)), impurities were extracted with 0.5ml of ethyl acetate containing four internal standards (n-decane, n-pentadecane, n-eicosane and n-octacosane) and analyzed by gas chromatography with a flame ionization detector on a DB-5 capillary column (0.32mm i.d.x30m, film thickness 1.0mum). Fourteen characteristic peaks on chromatograms were selected for the comparison and classification of samples, and the data were evaluated by the Euclidean distance of the relative peak areas after logarithmic transformation. Sixty-nine samples seized in Japan and 42 seized in Thailand were analyzed. The samples were classified into four groups roughly by cluster analysis. In addition, when it was difficult to compare samples that had fewer impurities on chromatograms obtained from liquid-liquid extraction (LLE), solid-phase microextraction (SPME) was effective. Because many characteristic peaks were detected using SPME, SPME made it easy to compare samples of high purity. The combination of LLE and SPME was useful for impurity profiling of MA samples seized in different countries.     

Effect of Extraction Procedure and Gas Chromatography Temperature Program on Discrimination of MDMA Exhibits

Analysis of impurities in seized MDMA tablets can be used to determine the synthesis method used and to identify links among exhibits. However, no standardized method exists to generate impurity profiles, limiting comparisons among different laboratories. This research investigated the effect of extraction procedure and gas chromatography temperature program on the resulting impurity profiles. Five exhibits were extracted using liquid–liquid extraction (LLE) and headspace solid‐phase microextraction (HS‐SPME), then analyzed using two different temperature programs. Profiles were statistically assessed using principal components analysis. While LLE was more reproducible, more compounds were extracted using HS‐SPME, thus providing more informative chemical profiles. The longer temperature program (53 min vs. 36 min) allowed greater discrimination of exhibits, due to improved precision as a result of an extended hold time (12 min). This research further highlights the need for standardized extraction and analysis procedures to allow comparison of chemical profiles generated in different laboratories.     

Analysis of fatty acid ethyl esters in hair as possible markers of chronically elevated alcohol consumption by headspace solid-phase microextraction (HS-SPME) and gas chromatography-mass spectrometry (GC-MS)

Fatty acid ethyl esters (FAEE) are products of the nonoxidative ethanol metabolism, which are known to be detectable in blood only about 24h after the last alcohol intake. After deposition in hair they should be suitable long-term markers of chronically elevated alcohol consumption. Therefore, a method for the analysis of ethyl myristate, ethyl palmitate, ethyl oleate and ethyl stearate from hair was developed based on the extraction of the hair sample by a dimethylsulphoxide (DMSO)/n-hexane mixture, separation and evaporation of the n-hexane phase and application of headspace solid-phase microextraction (HS-SPME) in combination with gas chromatography-mass spectrometry (GC-MS) to the extract. For use as internal standards, the corresponding D(5)-ethyl esters were prepared. The HS-SPME/GC-MS measurements were automatically performed using a multi-purpose sampler. The detection limits of the FAEE were between 0.01 and 0.04ng/mg and the reproducibility was between 3.5 and 16%. By application of the method to hair samples of 21 fatalities with known heavy alcohol abuse 0.045-2.4ng/mg ethyl myristate, 0.35-13.5ng/mg ethyl palmitate, 0.25-7.7ng/mg ethyl oleate and 0.05-3.85ng/mg ethyl stearate were measured. For social drinkers (30-60g ethanol per week), the concentrations were about one order of magnitude smaller. For 10 teetotalers negative results or traces of ethyl palmitate were found. It was shown by supplementary investigations in single cases that FAEE are also present in sebum, that there is no strong difference in their concentrations between pubic, chest and scalp hair, and that they are detectable in hair segments after a 2 months period of abstinence. From the results follows that the measurement of FAEE concentrations in hair is a useful way for a retrospective detection of alcohol abuse.     

Development of a harmonised method for the profiling of amphetamines VI: Evaluation of methods for comparison of amphetamine

Amphetamine samples were analysed by gas chromatography-mass spectrometry (GC-MS), and the peak areas of 33 target compounds were transformed by applying various pretreatment techniques. The objective was to optimise the ability of a number of distance metrics to establish links between samples of amphetamine originating from the same batch (henceforth referred to as linked distances). Furthermore, partial least squares discriminant analysis (PLS-DA) was used to evaluate the effects of various pretreatment methods on separation of amphetamine batches synthesised by the Leuckart reaction, reductive amination of benzyl methyl ketone, and the nitrostyrene route. The most efficient way to pretreat GC-MS data varied for the different distance metrics, although best results were obtained when data were normalised to the sum of peak areas, and either the fourth root or a logarithm was applied to the normalised data. When pretreating normalised data by fourth root transformation, Pearson correlation was the distance metric that was most successful at finding linked samples. Normalisation and the use of fourth root also represented the best method of pretreating data when employing PLS-DA to separate samples synthesised by different routes. To achieve a faster and more user-friendly procedure for evaluating chromatograms, experiments were performed in which the number of target compounds used to compare samples was reduced. The effect of each compound that was removed was studied by applying PLS-DA and by using Pearson correlation to calculate linked distances as well as unlinked distances (between samples from different batches of amphetamine). Considering both links between samples from the same batch and separation of samples synthesised by different routes, the best results were obtained with the data set comprising 26 compounds. Finally, it was found that the profiling method developed in this work was superior to an existing technique with respect to separating linked and unlinked distances.     

生物检材中甲基苯丙胺及苯丙胺的分析研究进展

对近几年国内外22篇有关生物检材中甲基苯丙胺及苯丙胺测定的文献进行了综述。介绍了血、尿、毛发等生物检材的收集与预处理方法,比较了生物检材中甲基苯丙胺及苯丙胺的液-液萃取(LLE)、固相萃取(SPE)、固相微萃取(SPME)和顶空固相微萃取(HS-SPME)等提取方法,以及内标的选取、不同的衍生化方法和包括免疫、GC/MS、GC/NPD、GC/ECD、GC/FID、HPLC、HPCE在内的各种检测方法。最后,对分析结果的评定进行了讨论。     

Optimization of extraction parameters for the chemical profiling of 3,4-methylenedioxymethamphetamine (MDMA) tablets

The extraction of impurities from illegally produced 3,4-methylenedioxymethamphetamine (MDMA) has been studied in order to optimize the parameters. Two different MDMA samples were used. Particular attention was paid to the influence of the pH, the evaporation step, and the sample storage. The method used was an extraction of impurities by diethyl ether from a buffer solution at pH 11.5, followed by gas chromatography (GC) mass spectrometric (MS) analyses after a dryness concentration under monitored conditions of the ethereal extract. Repeat extractions of the same sample gave an average relative standard deviation (RSD) of less than 8.5% within day and less than 10.5% between days.     

全血中扎来普隆两种萃取方法的比较

目的建立血样中扎来普隆的液液萃取和固相萃取方法。方法液液萃取方法是在碱性条件下用二氯甲烷提取。固相萃取是采用OasisHLB固相萃取柱提取,萃取液均用GC/NPD检验,并对其进行比较。结果血样中扎来普隆固相萃取平均回收率达89%以上,液液萃取平均回收率为84%,GC/NPD最低检出限为2×10-2μg.mL-1。结论两种方法均能满足实际检案的需求,而固相萃取方法在减少仪器损耗和内源性杂质干扰方面具有较大的优势。