Forensic analysis of explosives using isotope ratio mass spectrometry (IRMS) — Discrimination of ammonium nitrate sources

An evaluation was undertaken to determine if isotope ratio mass spectrometry (IRMS) could assist in the investigation of complex forensic cases by providing a level of discrimination not achievable utilising traditional forensic techniques. The focus of the research was on ammonium nitrate (AN), a common oxidiser used in improvised explosive mixtures.The potential value of IRMS to attribute Australian AN samples to the manufacturing source was demonstrated through the development of a preliminary AN classification scheme based on nitrogen isotopes. Although the discrimination utilising nitrogen isotopes alone was limited and only relevant to samples from the three Australian manufacturers during the evaluated time period, the classification scheme has potential as an investigative aid.Combining oxygen and hydrogen stable isotope values permitted the differentiation of AN prills from three different Australian manufacturers. Samples from five different overseas sources could be differentiated utilising a combination of the nitrogen, oxygen and hydrogen isotope values. Limited differentiation between Australian and overseas prills was achieved for the samples analysed.The comparison of nitrogen isotope values from intact AN prill samples with those from post-blast AN prill residues highlighted that the nitrogen isotopic composition of the prills was not maintained post-blast; hence, limiting the technique to analysis of un-reacted explosive material.     

Quantification and aging of the post-blast residue of TNT landmines

Post-blast residues are potential interferents to chemical detection of landmines. To assess the potential problem related to 2,4,6-trinitrotoluene (TNT), its post-blast residue was identified and quantified. In the first part of this study laboratory-scale samples of TNT (2 g) were detonated in a small-scale explosivity device (SSED) to evaluate the explosive power and collect post-blast residue for chemical analysis. Initiator size was large relative to the TNT charge; thus, issues arose regarding choice of initiator, residue from the initiator, and afterburning of TNT. The second part of this study detonated 75 to 150 g of military-grade TNT (typical of antipersonnel mines) in 55-gal barrels containing various witness materials (metal plates, sand, barrel walls, the atmosphere). The witness materials were analyzed for explosive residue. In a third set of tests, 75-g samples of TNT were detonated over soil (from Fort Leonard Wood or Sandia National Laboratory) in an indoor firing chamber (100 by 4.6 by 2.7 m high). Targeted in these studies were TNT and four explosive-related compounds (ERC): 2,4-dinitrotoluene (DNT), 1,3-dinitrobenzene (DNB), 2- and 4-aminodinitrotoluene (2-ADNT and 4-ADNT). The latter two are microbial degradation products of TNT. Post-blast residue was allowed to age in the soils as a function of moisture contents (5 and 10%) in order to quantify the rate of degradation of the principal residues (TNT, DNT, and DNB) and formation of the TNT microbial degradation products (2-ADNT and 4-ADNT). The major distinction between landmine leakage and post-blast residue was not the identity of the species but relative ratios of amounts. In landmine leakage the DNT/TNT ratio was usually greater than 1. In post-blast residue it was on the order of 1 to 1/100th of a percent, and the total amount of pre-blast residue (landmine leakage) was a factor of 1/100 to 1/1000 less than post-blast. In addition, landmine leakage resulted in low DNT/ADNT ratios, usually less than 1, whereas pre-blast residues started with ratios above 20. Because with time DNT decreased and ADNT increased, over a month the ratio decreased by a factor of 2. The rate of TNT degradation in soil observed in this study was much slower than that reported when initial concentrations of TNT were lower. Degradation rates yielded half-lives of 40 and 100 days for 2,4-DNT and TNT, respectively.     

海洛因来源鉴定的新方法

毒品来源的鉴定是指对毒品样品中包含的来源信息进行提取拜分析,这有助于打击毒品犯罪.海洛因是危害我国的主要毒品,它的来源鉴定更引起人们的关注.本文介绍了国际上研究海洛因来源的三种方法,即研究海洛因样品中的各种有机杂质及其相对比例;研究海洛因样品中的痕量无机元素;研究海洛因及吗啡的稳定同位素相对比值.第三种方法能够反映样品的地域性特点,因而在来源鉴定方面有突出的优势.气相色谱-燃烧-同位素比值质谱法是同位素比值测定方法中用于海洛因来源鉴定的最佳手段.这一技术还可用于其他微量物证(如炸药、药品、油品等)的来源鉴别,因而在法庭科学领域内显示了广阔的应用前景.     

Forensic utility of carbon isotope ratio variations in PVC tape backings

Forensic interest in adhesive tapes with polyvinyl chloride (PVC) backings (electrical tape) derives from their use in a variety of illicit activities. Due to the range of physical characteristics, chemical compositions, and homogeneity within a single roll of tape, traditional microscopic and chemical analyses can offer a high degree of discrimination between tapes, permitting the assessment of potential associations between evidentiary tape samples. The carbon isotope ratios of tapes could provide additional discrimination among tape samples. To evaluate whether carbon isotope ratios may be able to increase discrimination of electrical tapes, particularly with regards to different rolls of tape of the same product, we assessed the δ(13)C values of backings from 87 rolls of PVC-based black electrical tape (~20 brands, >60 products) Prior to analysis, adhesives were removed to prevent contamination by adhering debris, and plasticizers were extracted because of concern over their potential mobility. This result is consistent with each of these tapes having approximately the same plasticizer δ(13)C value and proportion of carbon in these plasticizers. The δ(13)C values of the 87 PVC tape backings ranged between -23.5 and -41.3 (‰, V-PDB), with negligible carbon isotopic variation within single rolls of tape, yet large variations among tape brands and tape products. Within this tape population, carbon isotope ratios permitted an average exclusion power of 93.7%, using a window of +/-0.3‰; the combination of carbon isotope ratio measurement with additional chemical and physical analyses raises the discrimination power to over 98.9%, with only 41 out of a possible 3741 pairs of tape samples being indistinguishable. There was a linear relationship between the δ(13)C value of tape backings and the change in δ(13)C value with the extraction of plasticizers. Analyses of pre- and post-blast tape sample pairs show that carbon isotope signatures are within 0.3‰ of pre-blast values, indicating that carbon isotope values are largely preserved during an explosion.     

A case study on the application of isotope ratio mass spectrometry (IRMS) in determining the provenance of a rock used in an alleged nickel switching incident

The application of isotope ratio mass spectrometry (IRMS) in forensic science to establish the provenance of a range of questioned substances including soils, drugs, explosives, currency, ivory and rhino horn has been widely documented. The present study wishes to highlight the applicability of IRMS and specifically stable carbon IRMS in determining the provenance of a carbonate rock that was switched for nickel metal exported from South Africa to Israel. The technique employed effectively argued against a South African origin for the rock whilst simultaneously supporting an Israeli origin, enabling investigators to focus their attention accordingly. The study represents the first documented instance known to the authors where IRMS has been employed in the forensic geo-location of a rock.     

纸喷雾质谱在物证检验中的应用

物证检验中,建立简便、快捷、样品前处理步骤少的质谱分析方法一直是一大挑战。纸喷雾电离技术具有快速灵敏、经济高效、操作简便的特点,可有效解决物证检验中的难题。本文综述了纸喷雾电离质谱在物证检验领域相关应用的最新进展,主要包括毒物毒品分析、药物滥用、农残检测、食品及日用品安全、文书检验及爆炸物检测,并辅以展望。     

Analysis of hydrogen peroxide field samples by HPLC/FD and HPLC/ED in DC mode

The goal of this paper is to describe applications of two recently developed HPLC methods for the analysis and confirmation of the presence of hydrogen peroxide residues in field studies. The procedure utilizes two different HPLC systems, one with post-column derivatization followed by fluorescence detection (HPLC/FD), and the other with electrochemical detection (HPLC/ED). The two systems were utilized to detect hydrogen peroxide in a variety of typical forensic samples including pre- and post-blast samples, as well as a series of environmental control samples. Peroxide-based organic explosives were also examined due to their propensity to produce peroxide residues following detonation. Because samples collected from post-blast scenes are frequently shipped or stored prior to analysis, the effects of storage time, temperature and type of substrate material on the recovery of hydrogen peroxide residues were also investigated. The combined results of the study demonstrate the capability of two HPLC approaches with selective detection in the analysis and investigation of suspected incidents involving peroxide based explosives.     

Application of LC−QTOF/MS for the validation and determination of organic explosive residues on Ionscan® swabs

The identification and confirmation of trace explosive residues along with potential precursors and degradation products require a comprehensive laboratory analysis procedure. This study presents the determination of organic explosives consisting of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4,6-trinitrotoluene (TNT), 2,4,6,N-tetranitro-N-methylaniline (Tetryl), 1,3,5-trinitrobenzene (1,3,5-TNB) and pentaerythritol tetranitrate (PETN) by a high-resolution liquid chromatography quadrupole time-of-flight mass spectrometry (LC−QTOF/MS). The qualitative information including retention time, collision energy, precursor ions, and characteristic fragmentation pattern of each explosive were collected using an atmospheric pressure chemical ionization (APCI) in negative ion mode. The separation efficiency among five compounds was greatly achieved in this study. Four real explosive samples consisting of TNT, RDX, PETN and Tetryl and 12 Ionscan® quality control swabs from the Royal Thai Army were also tested to validate and verify the viability of the GC–MS method used to validate results from an Ionscan® system. The results showed that LC−QTOF/MS is a powerful technique for the identification and confirmation of thermally unstable organic explosives on Ionscan® swabs compared to a conventional GC−MS technique.     

Solid phase micro extraction coupled with on-column GC/ECD for the post-blast analysis of organic explosives

Gas chromatographic analysis with electron capture detection is very sensitive to post-blast residues and useful for the determination of organic explosive molecules. But many compounds extracted from the matrices may interfere with the explosives. Using SPME, most interfering compounds are eliminated so the identification is easier. Another advantage of the technique is a low limit of detection. In this study, four different SPME fibers were tested to analyze the most common encountered organic explosives including nitro aromatics, nitramines and nitro-esters. Different parameters were tested (desorption time, agitation, ...) and a special device has been created to optimize the agitation. Direct desorption effect of the SPME fiber on the column compared to normal split-splitless injection is shown. In this way, the degradation of the most sensitive molecules is decreased. An application to a real case is also described in this paper.     

Trace analysis of peroxide explosives by high performance liquid chromatography-atmospheric pressure chemical ionization-tandem mass spectrometry (HPLC-APCI-MS/MS) for forensic applications

An HPLC-APCI-MS(/MS) method for the (trace) analysis of the most commonly encountered peroxide explosives, hexamethylenetriperoxidediamine (HMTD) and triacetonetriperoxide (TATP), has been developed. With this method, HMTD and TATP have been analyzed in the same run. (Pseudo-)molecular ions of these peroxides have been obtained as base peak under the same condition. A series of product ions was produced from these pseudo-molecular ions ([HMTD - 1]+ and [TATP + NH4]+) in the MS/MS analysis. We also pioneered in showing that a TATP molecular ion [TATP + H]+ can be observed with HPLC-MS/MS. The limit of detection for HMTD and TATP was 0.26 and 3.3 ng, respectively, on column by HPLC-MS in the Full Scan mode and 0.08 and 0.8, respectively, by HPLC-APCI-MS/MS in Selected Reaction Monitoring (single mass unit) mode. The method presented has been applied successfully for the identification of peroxides in the bulk solid state (powder sample), as well as in post-blast extracts originating from a forensic case. For the post-blast extracts, the use of tandem MS has been shown clearly to be of crucial importance for the identification and detection of the peroxide explosives.     

The identification of the emulsifier component of emulsion explosives by liquid chromatography-mass spectrometry

ABSTRACT: The widespread availability of emulsion explosives for commercial blasting has inevitably lead to their diversion for criminal misuse. Present techniques for the characterization of emulsion explosives and their residues is generally based on the detection and identification of the oxidizer and the hydrocarbon components. Use of these components is problematic for residue identification because ammonium nitrate, waxes, and oils are relatively common in the urban environment and even their co-detection does not exclude them being sourced from materials other than explosives. The detection of the emulsifier component offers increased evidential value as certain emulsifiers used in explosive formulations are manufactured for that specific use, or have limited environmental distribution. In the current study liquid chromatography-mass spectrometry (LC-MS) was utilized for the characterization of two emulsifiers in common use; ethanolamine adducts of polyisobutylene succinic anhydride and sorbitol mono-oleate (SMO). The LC-MS technique enabled the detection of both emulsifiers in preblast samples; however, only SMO was detected in postblast residues. The analysis of the hydrocarbon component by gas chromatography-mass spectrometry was achieved in the same procedure.     

An initial evaluation of stable isotopic characterisation of post-blast plastic debris from improvised explosive devices

A number of two-way radios, similar to those which have been employed to initiate Improvised Explosive Devices (IEDs), were acquired from a commercial supplier and grouped into four pairs. Samples of plastic material were collected from five distinct regions of each radio and analysed by Infrared and Raman spectroscopy to identify the nature of the material. One radio of each pair was then subjected to detonation with a commercially available plastic explosive. The combination of radio and explosive was considered to be representative of the components of an IED. Following detonation, fragments were recovered and, where possible, identified as specific sampling points of the radio.A combination of δ²H and δ¹³C stable isotopic analysis of material from each of the five sampling points was found to provide a pattern which was characteristic of a given radio and provided a means to associate pairs of radios. When few fragments were recovered, no positive association could be made between the fragments and the paired, undamaged radio. This was attributed, in part, to manufacturing variation in the radios. However, when three or more post-blast fragments were recovered it was possible to associate these with the paired, undamaged radio with a high degree of certainty.     

Lead Theft—A Study of the “Uniqueness” of Lead from Church Roofs

In the United Kingdom, theft of lead is common, particularly from churches and other public buildings with lead roofs. To assess the potential to distinguish lead from different sources, 41 samples of lead from 24 church roofs in Northamptonshire, U.K, have been analyzed for relative abundance of trace elements and isotopes of lead using X‐ray fluorescence (XRF) and inductively coupled plasma mass spectrometry, respectively. XRF revealed the overall presence of 12 trace elements with the four most abundant, calcium, phosphorus, silicon, and sulfur, showing a large weight percentage standard error of the mean of all samples suggesting variation in the weight percentage of these elements between different church roofs. Multiple samples from the same roofs, but different lead sheets, showed much lower weight percentage standard errors of the mean suggesting similar trace element concentrations. Lead isotope ratios were similar for all samples. Factors likely to affect the occurrence of these trace elements are discussed.     

Forensic Analysis of Explosives Using Isotope Ratio Mass Spectrometry (IRMS)—Part 1: Instrument Validation of the DELTAplusXP IRMS for Bulk Nitrogen Isotope Ratio Measurements

Abstract: A significant amount of research has been conducted into the use of stable isotopes to assist in determining the origin of various materials. The research conducted in the forensic field shows the potential of isotope ratio mass spectrometry (IRMS) to provide a level of discrimination not achievable utilizing traditional forensic techniques. Despite the research there have been few, if any, publications addressing the validation and measurement uncertainty of the technique for forensic applications. This study, the first in a planned series, presents validation data for the measurement of bulk nitrogen isotope ratios in ammonium nitrate (AN) using the DELTA^plusXP (Thermo Finnigan) IRMS instrument equipped with a ConFlo III interface and FlashEA? 1112 elemental analyzer (EA). Appropriate laboratory standards, analytical methods and correction calculations were developed and evaluated. A validation protocol was developed in line with the guidelines provided by the National Association of Testing Authorities, Australia (NATA). Performance characteristics including: accuracy, precision/repeatability, reproducibility/ruggedness, robustness, linear range, and measurement uncertainty were evaluated for the measurement of nitrogen isotope ratios in AN. AN (99.5%) and ammonium thiocyanate (99.99+%) were determined to be the most suitable laboratory standards and were calibrated against international standards (certified reference materials). All performance characteristics were within an acceptable range when potential uncertainties, including the manufacturer’s uncertainty of the technique and standards, were taken into account. The experiments described in this article could be used as a model for validation of other instruments for similar purposes. Later studies in this series will address the more general issue of demonstrating that the IRMS technique is scientifically sound and fit‐for‐purpose in the forensic explosives analysis field.     

Forensic analysis of explosives using isotope ratio mass spectrometry (IRMS) — Preliminary study on TATP and PETN

The application of isotopic techniques to investigations requiring the provision of evidence to a Court is limited. The objective of this research was to investigate the application of light stable isotopes and isotope ratio mass spectrometry (IRMS) to solve complex forensic cases by providing a level of discrimination not achievable utilising traditional forensic techniques.Due to the current threat of organic peroxide explosives, such as triacetone triperoxide (TATP), research was undertaken to determine the potential of IRMS to differentiate samples of TATP that had been manufactured utilising different starting materials and/or manufacturing processes. In addition, due to the prevalence of pentaerythritoltetranitrate (PETN) in detonators, detonating cord, and boosters, the potential of the IRMS technique to differentiate PETN samples from different sources was also investigated.Carbon isotope values were measured in fourteen TATP samples, with three definite groups appearing in the initial sample set based on the carbon data alone. Four additional TATP samples (in a second set of samples) were distinguishable utilising the carbon and hydrogen isotopic compositions individually, and also in combination with the oxygen isotope values. The 3D plot of the carbon, oxygen and hydrogen data demonstrated the clear discrimination of the four samples of TATP. The carbon and nitrogen isotope values measured from fifteen PETN samples, allowed samples from different sources to be readily discriminated.This paper demonstrates the successful application of IRMS to the analysis of explosives of forensic interest to assist in discriminating samples from different sources. This research represents a preliminary evaluation of the IRMS technique for the measurement of stable isotope values in TATP and PETN samples, and supports the dedication of resources for a full evaluation of this application in order to achieve Court reportable IRMS results.     

GC法和GC/MS法在地区毒品情报分析中的应用

目的探讨气相色谱法(GC)和气相色谱/质谱联用法(GC/MS)在地区毒品情报分析中的应用,并用于实际样品分析。方法采用GC/MS法定性分析毒品样品中的主成分、痕量杂质、掺假剂和稀释剂,并选择GC/FID法和内标标准曲线法定量分析上述各组分,通过定性和定量数据的统计和分析,推断该地区的毒品状况。结果用GC/MS定性分析、GC/FID定量分析,和数据的统计比对,获得了某省某年27起海洛因毒品大案样品主成分、痕量杂质、掺假剂和稀释剂组成及含量的特征,发现该省缴获的大宗海洛因毒品主要以掺假和稀释后的产品出现,且咖啡因和扑热息痛为两种主要的掺假剂和稀释剂。结论GC/MS和GC/FID法在地区毒品情报分析和打击毒品犯罪中可以发挥重要作用。     

Sourcing explosives: A multi-isotope approach

Although explosives are easily identified with current instrumental techniques, it is generally impossible to distinguish between sources of the same substance. To alleviate this difficulty, we present a multi-stable isotope (δ¹³C, δ¹⁵N, δ¹⁸O, δD) approach for appraising the possibility of discriminating explosives. The results from 30 distinct PETN, TNT and ANFO samples show that the different families of explosives are clearly differentiated by both their specific isotope signatures and their combination with corresponding element concentrations. Coupling two or more of the studied isotope systematics yields an even more precise differentiation on the basis of their raw-material origin and/or manufacturing process.     

Stable isotope analysis of white paints and likelihood ratios

Architectural paints are commonly found as trace evidence at scenes of crime. Currently the most widely used technique for the analysis of architectural paints is Fourier Transformed Infra-Red Spectroscopy (FTIR). There are, however, limitations to the forensic analysis of white paints, and the ability to discriminate between samples.Isotope ratio mass spectrometry (IRMS) has been investigated as a potential tool for the analysis of architectural white paints, where no preparation of samples prior to analysis is required. When stable isotope profiles (SIPs) are compared, there appears to be no relationship between paints from the same manufacturer, or between paints of the same type. Unlike existing techniques, IRMS does not differentiate resin samples solely on the basis of modifier or oil-type, but exploits additional factors linked to samples such as geo-location where oils added to alkyd formulations were grown. In combination with the use of likelihood ratios, IRMS shows potential, with a false positive rate of 2.6% from a total of 1275 comparisons.     

Visual detection of trace nitroaromatic explosive residue using photoluminescent metallole-containing polymers

The detection of trace explosives is important for forensic, military, and homeland security applications. Detection of widely used nitroaromatic explosives (trinitrotoluene [TNT], 2,4-dinitrotoluene [DNT], picric acid [PA]) was carried out using photoluminescent metallole-containing polymers. The method of detection is through the quenching of fluorescence of thin films of the polymer, prepared by spray coating organic solutions of the polymer, by the explosive analyte. Visual quenching of luminescence (lambda(em) approximately 400-510 nm) in the presence of the explosive is seen immediately upon illumination with near-UV light (lambda(ex)=360 nm). Detection limits were observed to be as low as 5 ng for TNT, 20 ng for DNT, and 5 ng for PA. In addition, experiments with normal production line explosives and their components show that this technology is also able to detect composition B, Pyrodex, and nitromethane. This method offers a convenient and sensitive method of detection of trace nitroaromatic explosive residue.     

The discrimination of automotive clear coats by pyrolysis-gas chromatography/mass spectrometry and comparison of samples by a chromatogram library software

Identification particles used for the purpose of the post-blast identification of explosives have a coding system based on the combination of metal oxides and their various concentrations. These materials are composed of the polymeric matrix, iron powder (ferromagnetic properties), UV light active dyestuff and various metal oxides in a various ratios. A suitable analytical method has to be used for an accurate characterization of these metal components in the particles in order to find the required information, i.e. to determine the place and the year of production and as the case may be, also the production batch of misused explosives. In this work, the method of microwave digestion and flame atomic absorption spectrometry (F-AAS) was developed for an accurate determination of Zn, Mg, Cu and Pb in a few novel types of identification particles and applied to their characterization. When using specific sample treatment (digestion with a mixture of nitric acid with hydrochloric or hydrofluoric acid), the 3 sigma limits of detection (LODs) for the determination of Zn, Mg, Cu and Pb in 5mg original samples were 1.9, 0.2, 1.3 and 2.4 mg g(-1), respectively. The signal suppression due to the presence of HNO3+HCl or HNO3+HF was observed for Zn; therefore, the calibration solutions had to be prepared exactly with the same acids as those used for the sample mineralization. The determination of Mg, Cu and Pb was free of interferences; hence a simple calibration curve method could be adopted for attaining accurate results. The accuracy was checked by comparison of the results with those obtained by means of independent inductively coupled plasma optical emission spectrometry (ICP-OES). Good precision values, as relative standard deviation, in the range of 1-5% were obtained. A total number of 71 samples was analysed and classified by multivariate methods to prove the suitability of the procedure proposed for the purpose of the identification of explosives.